D-Link 3100 24P User Manual

D-Link 3100 24P - DGS Switch - Stackable Manual

Get D-Link 3100 24P - DGS Switch - Stackable PDF manuals and user guides
UPC - 790069304941
View all D-Link 3100 24P manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link 3100 24P manual content summary:

  • D-Link 3100 24P | User Manual - Page 1
    D-Link™ DGS-3100 SERIES GIGABIT STACKABLE MANAGED SWITCH User Manual V2.30
  • D-Link 3100 24P | User Manual - Page 2
    the entities claiming the marks and names or their products. D-Link Computer Corporation disclaims any proprietary interest in trademarks and trade names environment, this product may cause radio interference in which case the user may be required to take adequate measures. Warnung! Dies ist ein
  • D-Link 3100 24P | User Manual - Page 3
    Using the Web-Based User Interface ...4 Understanding the D-Link Embedded Web Interface ...5 Using the Tool Menu ...7 Displaying the Stack Status...7 Locating Devices...7 Backing up and Restoring Configuration Files ...8 Resetting the Device ...9 Downloading the Firmware...10 Rebooting the System
  • D-Link 3100 24P | User Manual - Page 4
    56 Dual Image Services ...57 Firmware Information ...57 Config Firmware Image ...58 Telnet Setting ...59 CONFIGURING L2 FEATURES...60 Enabling Jumbo Frames...61 Configuring VLANs ...62 Understanding IEEE 802.1p Priority ...62 VLAN Description ...62 Notes about VLANs on the DGS-3100 Series ...62 IEEE
  • D-Link 3100 24P | User Manual - Page 5
    Information ...104 CONFIGURING QUALITY OF SERVICE ...109 Understanding QoS ...111 VLANs ...124 Configuring Port Authentication 802.1X ...125 Configuring MAC Authentication (by using Guest VLAN Configuring Local Enable Password...147 MONITORING THE PoE System Information ...168 Displaying and Editing
  • D-Link 3100 24P | User Manual - Page 6
    DEFINING ACCESS PROFILE LISTS...171 ACL Configuration Wizard...172 Defining Access Profile Lists...174 Defining Access Rules Lists ...187 Finding ACL Rules ...190 Defining Time Ranges ...193 TECHNICAL SUPPORT...204
  • D-Link 3100 24P | User Manual - Page 7
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Preface This preface provides an overview to the guide, and includes the following sections:  System Overview  Viewing the Device  Device Management Methods  User Guide Overview  Intended Audience  Notes, Notices, and Cautions 
  • D-Link 3100 24P | User Manual - Page 8
    Switch User Manual System Overview The DGS-3100 series and the DGS-3100-24TG Gigabit Ethernet Switches enhance networks by providing a powerful switch that eliminates network bottlenecks, enabling network administrators to fine tune network configurations. The DGS-3100 series and the DGS-3100-24TG
  • D-Link 3100 24P | User Manual - Page 9
    Series Gigabit Stackable Managed Switch User Manual Device Management Methods The DGS-3100 series and DGS-3100-24TG provide different methods for managing the device including:  Web Based Management Interface  SNMP-Based Management  Command Line Console Web Based Management Interface Once the
  • D-Link 3100 24P | User Manual - Page 10
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your device. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
  • D-Link 3100 24P | User Manual - Page 11
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual product does not operate correctly when you follow the operating instructions.  Keep your system away from radiators and heat see the appropriate section in your troubleshooting guide or contact your trained service provider.  Do not push
  • D-Link 3100 24P | User Manual - Page 12
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual  When connecting or disconnecting power to hot-pluggable power to components in the rack. Do not step on or stand on any component when servicing other components in a rack. NOTE: A qualified electrician must perform all connections to DC
  • D-Link 3100 24P | User Manual - Page 13
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual CAUTION: The system chassis must be positively grounded to the rack cabinet frame. Do not attempt to with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. vii
  • D-Link 3100 24P | User Manual - Page 14
  • D-Link 3100 24P | User Manual - Page 15
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 1 GETTING STARTED To begin managing the device, simply run the browser installed on the management station and point it to the IP address defined for the device. For example; http://123.123.123.123. Please note that the proxy for session
  • D-Link 3100 24P | User Manual - Page 16
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Accessing the Boot/Startup Menu Functions The following configuration functions are performed from the Boot (Startup) menu:  Downloading Software  Set Terminal Baud-Rate  Defining Stacking Units To display the Startup menu: 1. During
  • D-Link 3100 24P | User Manual - Page 17
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The following prompt is displayed: Set new device Baud (stack membership number). Unit ID 0 is allocated for auto-numbering, which is the factory default. Refer to Managing Stacking for further reference. To access the stack menu: 1. On
  • D-Link 3100 24P | User Manual - Page 18
    to various switch configuration and management windows, allows you to view performance statistics, and permits you to graphically monitor the system status. The screen captures in this Guide represent the DGS-3100-48 48 port device. The Web pages in the 24 port and the DGS-3100-24TG devices may
  • D-Link 3100 24P | User Manual - Page 19
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Understanding the D-Link Embedded Web Interface The D-Link Embedded provides a view of the device, an information or table area, and configuration instructions. Stacking Status View Located at the bottom left corner of the home page,
  • D-Link 3100 24P | User Manual - Page 20
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual View 5 Device Application Buttons 6 Stacking Status View Description the Switch's ports and expansion modules, showing port activity, . Provides a graphic representation of the stacking links and ports status. Table 1-2. Main Areas 6
  • D-Link 3100 24P | User Manual - Page 21
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Using the Tool Menu The tool menu contains menu options for:  Displaying the Stack Status  Locating Devices  Backing up and Restoring Configuration Files  Resetting the Device  Downloading the Firmware  Rebooting the System
  • D-Link 3100 24P | User Manual - Page 22
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Backing up and Restoring Configuration Files The Config Backup and Restore Page contains fields for downloading TFTP server. The possible field values are: Server IP - Specifies the TFTP Server IP Address to which files are backed up or
  • D-Link 3100 24P | User Manual - Page 23
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Select HTTP or TFTP field. 3. Define the selected server method fields. To backup files, click . To restore files, click . Resetting the Device The Factory Reset Page restores the factory defaults. To restore the device to the
  • D-Link 3100 24P | User Manual - Page 24
    Managed Switch User Manual Downloading the Firmware The 'Firmware Download' web page is used to download the firmware files that will be used to manage the device. NOTE: Firmware version 1.x.x supports 4 SKUs od DGS-3100 series: DGS-3100-24, DGS-310024P, DGS-3100-48 and DGS-3100-48P, Firmware
  • D-Link 3100 24P | User Manual - Page 25
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The Firmware Download Page contains the following fields: Field Description HTTP Download Indicates that the Firmware file is downloaded via an HTTP server. Unit - Indicates if the Firmware file is downloaded to a specific stacking
  • D-Link 3100 24P | User Manual - Page 26
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Rebooting the System The System Reboot Page provides a method for selecting one, or all of the units to be rebooted. To reboot the system: 1. Click >
  • D-Link 3100 24P | User Manual - Page 27
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Using the Web System Components The following table selected fields Deletes VLAN Identification Starts downloading system files. Edit Factory Reset Modifies configuration Information Resets the factory defaults Find System Reboot
  • D-Link 3100 24P | User Manual - Page 28
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2 CONFIGURING BASIC CONFIGURATION This section contains information for viewing device information, defining IP addresses, managing stacking, defining port parameters, configuring system user accounts, configuring and managing system logs,
  • D-Link 3100 24P | User Manual - Page 29
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing user-defined system name. The field range is 0-31 characters. System Location Displays the location where the system is currently running. The field range is 0-31 characters. Firmware Version Displays the installed software
  • D-Link 3100 24P | User Manual - Page 30
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field MAC Address Description Displays the MAC address assigned to the device. IP Address Displays the IP address assigned to the device. Subnet Mask Displays the subnet mask assigned to the device. Default Gateway Displays the
  • D-Link 3100 24P | User Manual - Page 31
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual assigned to the device Firmware Version Displays the stacking member's software version number. Hardware the amount of time the device times out when no user activity occurs. The default is 10 minutes. 2. Define the System Name field.
  • D-Link 3100 24P | User Manual - Page 32
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining IP Addresses The IP Address Page contains fields for assigning IP addresses. Packets are forwarded to the default IP when frames are sent to a remote network via the Default Gateway. The configured IP address must belong to the
  • D-Link 3100 24P | User Manual - Page 33
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Managing Stacking Stacking enhances network flexibility by building virtual switches with more ports then are available in a single device. Stacks are managed by stacking member which called Stack Master., All other stacking members serve
  • D-Link 3100 24P | User Manual - Page 34
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Unit ID assignments or a master nor a backup master unless their ID is changed by the system administrator or reset to the factory default firstly). Electing a Stacking Master Whenever a stacking member (or more than one) comes
  • D-Link 3100 24P | User Manual - Page 35
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual  If one of the master enabled stacking members assigned the Unit ID 2. - If the stack contains one or more stacking members set to the factory default states, and there is no Unit ID assigned to a stacking member, then the Stack Master is
  • D-Link 3100 24P | User Manual - Page 36
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Allocating Unit IDs/Resolving Unit ID Conflicts Once the Stack Master is elected, it allocates the Unit IDs to the stacking members that do not have a Unit ID. Stacking members that do not have a Unit ID operate in the Factory Default link
  • D-Link 3100 24P | User Manual - Page 37
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Building Stacks - Quick Start The DGS-3100 series supports the following stacking scenarios:  Building a new stack from scratch  Increasing the stack by adding units to an existing stack This section contains the following topics: 
  • D-Link 3100 24P | User Manual - Page 38
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual This section contains the following topics:  Building New Manually Ordered Stacks  Adding Stacking Members to an Existing Manually Ordered Stack Building New Manually Ordered Stacks To build new a self ordered stack: 1. Connect the units
  • D-Link 3100 24P | User Manual - Page 39
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual - If the new stacking member has a Unit ID of 1 or 2, i.e. the stacking member is a master enabled unit, the new stacking member initiates the Master Election
  • D-Link 3100 24P | User Manual - Page 40
    Switch User Manual Unit ID 1, and serving as the stack Backup master, while the already running stacking member with Unit ID 2 remains the active Stack Master.  The Stack Master performs Unit ID Allocation and Conflict Resolution process. - If the new stacking member is in the Factory Default
  • D-Link 3100 24P | User Manual - Page 41
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual - If the Stack Master remains in this running stack, and the stacking members are not in the Factory Default Mode, the stacking members are not reassigned Unit IDs. Resetting the stacking members will initiate Unit ID auto-assignment. No
  • D-Link 3100 24P | User Manual - Page 42
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Merging Stacks This example assumes that the user would like to merge two working stacks. This creates one stack from two separate stacks. There are two scenarios: If new stacking members are powered
  • D-Link 3100 24P | User Manual - Page 43
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual  A running stacking member group is added originally belonged to the group managed by the newly elected master. The original switches retain their ID assignments and configurations. The stacking members that originally belonged to the
  • D-Link 3100 24P | User Manual - Page 44
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Stacking The Stacking Settings Page allows network managers to execute force master and to change each and every unit its own unit ID. To complete the changing process the user the device rboot. reset 2. Select the Stacking
  • D-Link 3100 24P | User Manual - Page 45
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Ports  Configuring Port Properties  certain characteristics that are different from the other choices listed. The copper ports also support auto MDI/MDIX for cross over cables. To define port parameters: 1. Click Configuration
  • D-Link 3100 24P | User Manual - Page 46
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Enabled - Indicates that the interface is currently receiving and transmitting traffic. Disabled - Indicates that the interface is currently not receiving and not transmitting traffic. This is the default value. Speed
  • D-Link 3100 24P | User Manual - Page 47
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Port Properties The Port Description Page allows network Defines the port number to which the port parameters are configured. Description Defines a user-defined port description. 2. Define the Unit, From Port, To Port, and
  • D-Link 3100 24P | User Manual - Page 48
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual ARP Settings The Address Resolution Protocol (ARP) converts IP addresses into physical addresses and maps the IP address to a MAC address. ARP allows a host to communicate with other hosts only when the IP addresses of its neighbors are
  • D-Link 3100 24P | User Manual - Page 49
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring User Accounts User accounts including user passwords and access rights are defined on the User Accounts Page. To define user account information: 1. Click Configuration > User Accounts. The User Accounts Page opens: Figure 2-8
  • D-Link 3100 24P | User Manual - Page 50
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual To edit the User Accounts Page: 1. Select a name on the User List. 2. Click . 3. Define the value. 4. Click . The new access rights are saved, and device is updated. To delete a User Accounts Page entry: 1. Select an entry. 2.
  • D-Link 3100 24P | User Manual - Page 51
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual -The device is functioning, but an operational problem has occurred. Informational - Provides device information range is 1 - 65535. The default value is 514. 2. Define the Index, Severity, Server IP, Facility, and UDP Port fields.
  • D-Link 3100 24P | User Manual - Page 52
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual To delete a log entry: 1. Select the entry. 2. Click . The entry is deleted, and the device is updated. 38
  • D-Link 3100 24P | User Manual - Page 53
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring SNTP The device supports the Simple Network Time Protocol ( a GPS system) is used as the time source. Stratum 1 A server that is directly linked to a Stratum 0 time source is used as the time source. Stratum 1 time servers
  • D-Link 3100 24P | User Manual - Page 54
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defines the IP address of primary SNTP server from which SNTP Second Server Defines the IP address of secondary SNTP server range is 60-86400 seconds. The Poll Interval default is 1024 seconds. Field Time Setting Description Defines the
  • D-Link 3100 24P | User Manual - Page 55
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description clock (Military Time) For example, 9:00PM is configured as 21:00:00. 2. Select a time source in the Time Source field. 3. Define the fields. 4.
  • D-Link 3100 24P | User Manual - Page 56
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual  Lithuania - From the last weekend of March until the last weekend of October.  Luxembourg - From the last weekend of March until the last weekend of
  • D-Link 3100 24P | User Manual - Page 57
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual To configure the system time:  Click Configuration > dates. Daylight Saving Time Offset in Minutes Defines the local DST offset in minutes. The default time is 60 minutes. The possible field values are: 30 - Defines the local offset for
  • D-Link 3100 24P | User Manual - Page 58
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field From Which Week of the Month Description Defines MM Defines the time of day DST ends. The field format is Hour:Minutes based on the 24-hour clock (Military Time). For example, 9:00PM is configured as 21:00. DST Annual Settings
  • D-Link 3100 24P | User Manual - Page 59
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring SNMP Simple Network Management Protocol (SNMP) provides a method for managing network devices. The device supports the following SNMP versions:  SNMP version 1  SNMP version 2c  SNMP version 3 SNMP v1 and v2c The SNMP
  • D-Link 3100 24P | User Manual - Page 60
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Views SNMP views provide or block access to device features or aspects of features. For example, a view can be defined to show that SNMP view A has included access to Multicast groups, while SNMP view B has excluded access to
  • D-Link 3100 24P | User Manual - Page 61
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Groups The SNMP Group Table Page provides information for creating SNMP groups and assigning SNMP access control privileges to SNMP groups. Groups enable network managers to assign access rights to specific device features or
  • D-Link 3100 24P | User Manual - Page 62
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Notify View Name Description Defines a Notify view. The Notify view sends traps for the assigned SNMP - Authenticates SNMP messages, and ensures that the SNMP message's origin is authenticated. AuthPriv - Encrypts SNMP messages. 2.
  • D-Link 3100 24P | User Manual - Page 63
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Users The SNMP User Table Page enables assigning system users to SNMP groups and defining the user authentication method. To assign system users: 1. Click Configuration > SNMP Settings >SNMP User Table. The SNMP User Table
  • D-Link 3100 24P | User Manual - Page 64
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Auth-Protocol by Key Description Selects the authentication key type used to authenticate users. The possible field values are: MD5 - Defines that users are authenticated via a HMAC-MD5 algorithm key. SHA - Defines that users are
  • D-Link 3100 24P | User Manual - Page 65
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Communities Access rights are managed by defining communities, using the SNMP Community Table Page. When the community names are changed, access rights are also changed. SNMP communities are defined only for SNMP v1 and SNMP
  • D-Link 3100 24P | User Manual - Page 66
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Host Table The SNMP Host Table Page contains information for defining filters that determine whether traps are sent to specific host, as well as the trap type sent. To define the SNMP Host Table Page: 1. Click Configuration >
  • D-Link 3100 24P | User Manual - Page 67
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The SNMP Host Table Page contains the following fields: Field Description Host IP Address Defines the IP address to which the traps are sent. SNMP Version Defines the trap type. The possible field values are: SNMPV1 - Indicates that
  • D-Link 3100 24P | User Manual - Page 68
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining SNMP Engine ID The Engine ID is a unique identifier used for SNMP V3 implementations. This is an alphanumeric string used to identify the SNMP engine on the switch. To define the SNMP Engine ID: 1. Click Configuration > SNMP
  • D-Link 3100 24P | User Manual - Page 69
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Enabling SNMP Traps The SNMP Configuration Trap Page contains parameters for defining SNMP notification parameters. To enable SNMP notifications: To enable SNMP Traps: 1. Click Configuration > SNMP Settings > SNMP Trap Configuration. The
  • D-Link 3100 24P | User Manual - Page 70
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual DHCP Auto Configuration In the DHCP Auto Configuration Page, users can enable or disable automatic download of the latest image and configuration files from the DHCP server. During reboot, if DHCP Auto Configuration is enabled, the device
  • D-Link 3100 24P | User Manual - Page 71
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Dual Image Services The device contains two software images in its flash memory, one is for reboot and the other one is for backup. When a software download is successfully completed, the new image automatically becomes the new reboot file
  • D-Link 3100 24P | User Manual - Page 72
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Version Update Time Description An "*" indicates that this image file is used for reboot. Displays the image file's version number. Displays the time and date which the software was saved to the server. Config Firmware Image The
  • D-Link 3100 24P | User Manual - Page 73
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Telnet Setting The Telnet Setting allows users to enable or disable Telnet on the device. To enable or disable Telnet: 1. Click Configuration > Telnet Setting. The Telnet Setting opens: Figure 2-22 Telnet Setting
  • D-Link 3100 24P | User Manual - Page 74
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3 CONFIGURING L2 FEATURES This section contains information for enabling and configuring L2 Features. This section contains the following topics:  Enabling Jumbo Frames  Configuring VLANs  Configuring GVRP  Defining Trunking  Traffic
  • D-Link 3100 24P | User Manual - Page 75
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Enabling Jumbo Frames Jumbo Frame support is designed to enhance Frames on the device. Disabled - Disables Jumbo Frames on the device. This is the default value. 2. Select Enable in the Jumbo Frames field. Jumbo Frames are enabled only
  • D-Link 3100 24P | User Manual - Page 76
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring VLANs Understanding IEEE 802.1p Priority Priority alleviate problems associated with the delivery of time-critical data over congested networks. The quality of applications dependent on such data, such as video conferencing,
  • D-Link 3100 24P | User Manual - Page 77
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Term Untagging Description The act of stripping 802.1Q VLAN information out of the packet header. Ingress port A port on a switch where packets are flowing into the switch and VLAN decisions must be made. Egress port A port on a
  • D-Link 3100 24P | User Manual - Page 78
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 802.1Q VLAN Tags The figure below shows the 802.1Q VLAN tag. There are four .1Q Tag The EtherType and VLAN ID are inserted after the MAC source address, but before the original EtherType/Length or Logical Link Control. Due to the packet
  • D-Link 3100 24P | User Manual - Page 79
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Port VLAN ID Tagged packets (carrying the 802.1Q VID information) can be transmitted from one 802.1Q compliant network device to another with the VLAN information intact. This allows 802.1Q VLANs to span network devices (and the entire
  • D-Link 3100 24P | User Manual - Page 80
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual the ingress port. If it does not, Default VLANs The switch initially configures one VLAN, VID = 1, called 'default.' The factory default setting assigns all ports on the switch to the 'default.' Ports can't be removed from the default VLAN
  • D-Link 3100 24P | User Manual - Page 81
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining VLAN Properties The VLAN Configuration Page provides information and global parameters for configuring and working with VLANs. 1. Click L2 Features > 802.1Q VLAN. The VLAN Configuration Page opens: Figure 3-5. VLAN Configuration
  • D-Link 3100 24P | User Manual - Page 82
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3-6. Add/Edit VLAN Information Page The Add/Edit VLAN Information Page contains the following fields: Field VID Description Defines the VLAN ID. VLAN Name Defines the user-defined VLAN name. The field ranges up to 32
  • D-Link 3100 24P | User Manual - Page 83
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring GVRP GVRP timers need to be in the default values on all Layer 2-connected devices. If the GVRP timers are set differently on the Layer 2-connected devices, the GVRP application does not operate successfully. GARP VLAN
  • D-Link 3100 24P | User Manual - Page 84
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The GVRP Setting Page contains the following port. Admit All - Both tagged and untagged packets are accepted on the port. (This is the default value). 2. Select a stacking member in the Unit field. 3. Select the ports to and from which
  • D-Link 3100 24P | User Manual - Page 85
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Trunking The Trunking Configuration Page contains are: Static - The LAG is static; LACP is disabled on the LAG. (This is the default value). LACP - LACP is enabled on the device.. Ports Displays the ports which are included in
  • D-Link 3100 24P | User Manual - Page 86
    Series Gigabit Stackable Managed Switch User Manual Notes about Trunking on the DGS-3100 Series DGS-3100 series supports up to 32 LAGs per device (or stack). NOTE: A port must belong to the default VLAN when the user is adding the port to a LAG, After adding the port to the LAG, the LAG itself can
  • D-Link 3100 24P | User Manual - Page 87
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Traffic Segmentation The Traffic Segmentation Page enables administrators to force traffic from source ports to bypass the Forwarding Database (FDB), and forward all Unicast, Multicast
  • D-Link 3100 24P | User Manual - Page 88
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring LACP LAG ports can contain different media types if the ports are operating at the same speed. Aggregated links can be set up manually or automatically established by enabling LACP on the relevant links is the default value).
  • D-Link 3100 24P | User Manual - Page 89
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining IGMP Snooping When IGMP Snooping is Disables IGMP Snooping on the device. (This is the default value). VLAN ID Specifies the VLAN ID. VLAN Name Displays the user-defined VLAN name. Leave Timer Defines the time a host waits
  • D-Link 3100 24P | User Manual - Page 90
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Host Timeout Description Defines the time the host waits to receive a message before timing out. The default time is 260 seconds. The field range is 60-16711450 seconds. Router Timeout Defines the time the Multicast router waits
  • D-Link 3100 24P | User Manual - Page 91
    -3100 Series Gigabit Stackable Managed Switch User Manual 2. Click . The IGMP Snooping and Static Router Ports Settings Page opens: Figure 3-12. IGMP Snooping and Static Router Ports Settings Page The IGMP Snooping and Static Router Ports Settings Page contains the following fields: Field VLAN
  • D-Link 3100 24P | User Manual - Page 92
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Enable - Enables IGMP Snooping on the VLAN. Disable - Disables IGMP Snooping on the VLAN Querier State Defines the IGMP Querier status on the VLAN. The possible field values are: Enabled - Enables an IGMP Querier on
  • D-Link 3100 24P | User Manual - Page 93
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining MLD Snooping Multicast Listener Discovery (MLD) Snooping performs the same function for IPv6 multicast routers as IGMP Snooping does for IPv4 multicast routers. The device supports two versions of MLD Snooping: - MLDv1 Snooping
  • D-Link 3100 24P | User Manual - Page 94
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The MLD Snooping Page contains the following fields MLD Snooping on the device. (This is the default value). VLAN ID Specifies the VLAN ID. VLAN Name Displays the user-defined VLAN name. Done Timer Specifies the time interval in
  • D-Link 3100 24P | User Manual - Page 95
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3-14. MLD Snooping & Static Router Ports Settings Page The MLD Snooping & Static Router Ports Settings Page contains the following fields: Field VLAN ID Description Specifies the VLAN ID VLAN Name Displays the user default
  • D-Link 3100 24P | User Manual - Page 96
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Unit Static Router Ports Ports Dynamic Router Ports Ports Forbidden Router Ports Ports Description Defines the unit number. Defines the port numbers in the
  • D-Link 3100 24P | User Manual - Page 97
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Port Mirroring Switches user to specify that a desired 'target' port receives a copy of all traffic passing through a designated 'source' port. In order to activate Port Mirroring, the target port must belong to the default VLAN
  • D-Link 3100 24P | User Manual - Page 98
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Both Description Defines the port mirroring on both receiving and transmitting ports. None Defines that port mirroring is not applied to the ports. 2. Define
  • D-Link 3100 24P | User Manual - Page 99
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Spanning Tree Spanning Tree Protocol (STP) provides tree , resulting in increased traffic and reducing network efficiency. The device supports the following STP versions: Version Description Classic STP Provides a single
  • D-Link 3100 24P | User Manual - Page 100
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Spanning Tree Global Parameters While Classic STP or disables STP globally on the switch. The default is Disabled. STP Version Defines the desired version of STP to be implemented on the switch. There are three choices: STP
  • D-Link 3100 24P | User Manual - Page 101
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Bridge Priority (0 - 65535) Description Specifies the selected spanning tree instance device priority. The field range is 0-65535. The default The Global STP status default was 'Ebable' in previous software versions and was changed
  • D-Link 3100 24P | User Manual - Page 102
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining STP Port Settings STP can be set up on a port per port basis. In addition to setting Spanning Tree parameters for use at the switch level, the switch enables configuring groups of ports, in which case each port-group has its own
  • D-Link 3100 24P | User Manual - Page 103
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual are: True - Indicates a point-to-point (P2P) link, P2P ports transition to a forwarding state rapidly thus benefiting The default setting is Auto. State Set to enable or disable STP for the selected group of ports. The default is Enabled
  • D-Link 3100 24P | User Manual - Page 104
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Multiple Spanning Tree Configuration Identification Multiple Spanning Tree (MSTP) provides various load balancing scenarios by allowing multiple VLANs to be mapped to a single spanning tree instance, providing multiple pathways
  • D-Link 3100 24P | User Manual - Page 105
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Remove - Indicates that edit type is remove. VID List (1-4094) Displays the VID List. 2. Define the configuration name and revision level. 3. Click . 4. Click
  • D-Link 3100 24P | User Manual - Page 106
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description 200,000,000. The default value is automatically set cost, according to its speed. Default when two ports are connected in a loop by a point-to-point link or when a LAN has two or more connections connected to a shared
  • D-Link 3100 24P | User Manual - Page 107
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Forwarding and Filtering This section contains it is discarded. Aging time is a global (FDB) database setting. VID Defines the VLAN ID. MAC Address Defines the Unicast MAC address to which packets are forwarded. Unit Defines
  • D-Link 3100 24P | User Manual - Page 108
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click . 3. Define the values. and LAGs attached to the Multicast service group in the Ports and LAGs tables. Ports can be following fields: Field VID Description Defines the VLAN ID Multicast MAC Address Defines the Multicast
  • D-Link 3100 24P | User Manual - Page 109
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Egress Description Defines the Egress ports per as None or Egress; - Alternatively, click to select the ports individually. The default is 1-48 None. 4. Click .The Multicast forwarding settings are applied to the port, and
  • D-Link 3100 24P | User Manual - Page 110
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The Multicast Filtering Mode Page contains the following Multicast groups. Forward Unregistered Groups - Forwards unregistered Multicast groups. This is the default mode. 2. Define the Unit and Filtering Mode fields. 3. Select either All
  • D-Link 3100 24P | User Manual - Page 111
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring LLDP The Link Layer Discovery Protocol (LLDP) allows troubleshooting are sent in the packet Type Length Value (TLV) field. LLDP devices must support chassis and port ID advertisement, as well as system name, system ID, system,
  • D-Link 3100 24P | User Manual - Page 112
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field LLDP Status LLDP Forward Hold Multiplier times the Message TX Interval. The possible field values are 2 - 10. The default is 4. Defines the time delay in seconds between successive LLDP frame transmissions initiated by value or
  • D-Link 3100 24P | User Manual - Page 113
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3-17. LLDP Port Setting Page The notification on the port. Disabled - Disables LLDP notification on the port. This is the default. Admin Status Specifies the LLDP transmission mode on the port. The possible field values are:
  • D-Link 3100 24P | User Manual - Page 114
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining LLDP Basic TLV Settings The LLDP Basic TLVS Setting Page displays LLDP basic TLV port information and contains parameters for configuring LLDP basic TLV
  • D-Link 3100 24P | User Manual - Page 115
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Enabled - Enables the System Capabilities TLV on the port. Disabled - Disables the System Capabilities TLV on the port. 2. Define the Unit, From Port,
  • D-Link 3100 24P | User Manual - Page 116
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing LLDP Local Port Information The LLDP Local Port Brief Page displays LLDP local port information. 1. Click L2 Features > LLDP > LLDP Local Port Brief. The
  • D-Link 3100 24P | User Manual - Page 117
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click . The LLDP Local Port Normal Page is displayed. Figure 3-21. LLDP Local Port Normal Page 3. To view the detailed MAC/PHY Configuration Status for
  • D-Link 3100 24P | User Manual - Page 118
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The LLDP Local Misc Detail Information Page contains is displayed. Port Indicates the port number. Entry Indicates the the device's Media Service Access Point (MSAP) entry number. Chassis ID Subtype Displays the chassis ID subtype.
  • D-Link 3100 24P | User Manual - Page 119
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Chassis ID Port ID Subfype Port ID the port description. 2. Click . The LLDP Remote Port Normal Page is displayed. Figure 3-24. LLDP Remote Port Normal Page 3. To view the detailed Management Address information for the entry,
  • D-Link 3100 24P | User Manual - Page 120
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3-25. LLDP Management Address Detail Information Page The LLDP Management Address Detail Information Page contains the following fields: Field Port Description Indicates the port
  • D-Link 3100 24P | User Manual - Page 121
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 3-26. LLDP Remote Misc Detail Information Page 6. Click to return to return to the LLDP Remote Port Normal Page. 7. To view the detailed information
  • D-Link 3100 24P | User Manual - Page 122
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The LLDP Remote Unknown TLVs Detailed Information Page contains the following fields: Field Port Entry Description Indicates the port number. Indicates the entry number. Unknown
  • D-Link 3100 24P | User Manual - Page 123
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 4 CONFIGURING QUALITY OF SERVICE Configuring 1p Priority tagging is alleviate problems associated with the delivery of time-critical data over congested networks. The quality of applications dependent on such data, such as video
  • D-Link 3100 24P | User Manual - Page 124
    -3100 Series Gigabit Stackable Managed Switch User Manual Figure 4-1. Mapping QoS on the Switch The picture above shows the default priority setting for the Switch. Class-3 has the highest priority of the four priority queues on the Switch. In order to implement QoS, the user is required to instruct
  • D-Link 3100 24P | User Manual - Page 125
    be configured at higher class than WRR. If the user configures WRR, at least two queues should be configured as WRR. Remember that the DGS-3100 series has four priority queues (and eight Classes of Service) for each port on the Switch. This section contains the following topics:  Defining Bandwidth
  • D-Link 3100 24P | User Manual - Page 126
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Bandwidth Settings The Bandwidth Control Page allows limitations on the port. (This is the default value). Disabled -Enables egress bandwidth limitations on the port. When disabled, the user can enter a limit value in the TX
  • D-Link 3100 24P | User Manual - Page 127
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Define the Unit, From Port, To Port, No Limit and Ingress Rate fields. 3. Click . The bandwidth settings are defined, and the device is updated. 113
  • D-Link 3100 24P | User Manual - Page 128
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Storm Control Storm control limits the selected port. Disable - Disables storm control on the selected port. (This is the default value) Threshold (35001000000) Indicates the maximum rate (kilobits per second) at which 'storm
  • D-Link 3100 24P | User Manual - Page 129
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Mapping Ports to Packet Priorities The 802.1P Default Priority Page provides traffic classification. by assigning priority values per port. The priority value is assigned when packet arrives to a port with an empty priority
  • D-Link 3100 24P | User Manual - Page 130
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Mapping Priority to Classes (Queues) The 802.1P User Priority Page allows network managers to assign priority tags to classes (queues). If a network manager defines a priority of 01 to Class 3, all packets arriving with
  • D-Link 3100 24P | User Manual - Page 131
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring QoS Scheduling Mechanism The QoS Scheduling the queue priority. Traffic with the highest Class of Service is the first traffic. That is, the highest class of service will finish before other queues empty. Round Robin -
  • D-Link 3100 24P | User Manual - Page 132
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Multi-Layer CoS Settings For network administrators wanting to configure Multi Layer CoS settings, implementation in the switch the following links: - Access Profile List - ACL Configuration Wizard 2. Click the desired link. The
  • D-Link 3100 24P | User Manual - Page 133
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 5 SECURITY FEATURES This section contains information for enabling and configuring device security including user accounts.  Configuring Safeguard Engine  Configuring Trust Host  Configuring Port Security  Configuring Guest VLANs 
  • D-Link 3100 24P | User Manual - Page 134
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Safeguard Engine The Safeguard Engine Page field values are: Enabled - Enables the safeguard engine on the device. This is the default value. Disabled - Disables the safeguard engine on the device. 2. Set the safeguard engine
  • D-Link 3100 24P | User Manual - Page 135
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Trust Host The Trusted Host Page permits network managers to manage the device from remote stations. Network managers can configure up to three remote stations. Ensure that the remote stations are configured with the IP address
  • D-Link 3100 24P | User Manual - Page 136
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Port Security Network security can be increased by limiting access on a specific port only to users after the device has been reset. To define port security: on the device. This is the default value. Max Address(0-64) 0 means
  • D-Link 3100 24P | User Manual - Page 137
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Max Learning Addr Description Indicates the number of MAC addresses that can be learned on the port. 2. Define the Unit, From Port, To Port,
  • D-Link 3100 24P | User Manual - Page 138
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Guest VLANs Guest VLANs provide limited network access to authorized ports. If a port is denied network access via port-based authorization, but the Guest VLAN is enabled, the port receives limited network access. For example,
  • D-Link 3100 24P | User Manual - Page 139
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Port Authentication 802.1X Port-based authentication authenticates users on a per-port/per mac basis via an external server. Only authenticated and approved system users to access system services. The Authentication Server
  • D-Link 3100 24P | User Manual - Page 140
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual To enable the 802.1X: 1. Click Security > 802. before EAP requests are resent to the supplicant. The field value is in seconds. The field default is 30 seconds. ServerTimeout (1-65535) sec Defines the amount of time that lapses before the
  • D-Link 3100 24P | User Manual - Page 141
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual the port control is Force Unauthorized and the port link is down, or the port control is Auto but values are: Port Base - Enables 802.1X on ports. This is the default value. MAC Base - Enables 802.1xon MAC addresses. 2. Enable or disable
  • D-Link 3100 24P | User Manual - Page 142
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual To enable MAC Authentication: 1. Click Security > 802 EAP requests are resent to the supplicant. The field value is in seconds. The field default is 30 seconds. ServerTimeout (1-65535) sec Defines the amount of time that lapses before the
  • D-Link 3100 24P | User Manual - Page 143
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Disabled - Disables re-authenticating the port or MAC addresses after the port or MAC address authentication has timed out. Control Indicates the host status. If there is an asterisk (*), the port is either not linked
  • D-Link 3100 24P | User Manual - Page 144
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring MAC Authentication (by using Guest VLAN, 802.1X and Radius pages) This is the sequence of operatons required to configure MAC Authentication in DGS-3100 series. 1. In order to configure a guest VLAN, the user is required to
  • D-Link 3100 24P | User Manual - Page 145
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3. After the ports were assigned to the Guest VLAN, the user needs to configure a Radius Server that will hold the MAC Authentication database. This should be done via click Security > 802.1X > Authentic RADIUS Server page
  • D-Link 3100 24P | User Manual - Page 146
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 5. The second step on Security > 802.1X > 802.1X Setting page will be configuration of the required ports as 'MAC Based' authentication (opposite to 'Port
  • D-Link 3100 24P | User Manual - Page 147
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining RADIUS Settings Remote Authorization Dial-In User Service (RADIUS) servers provide additional security for networks. RADIUS servers provide a centralized authentication method for management access. The default parameters are user
  • D-Link 3100 24P | User Manual - Page 148
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 4. Define the authentication port in the Authentic Port field. 5. Define the accounting port in the Accounting Port field. 6. Define the authentication and encryption key in
  • D-Link 3100 24P | User Manual - Page 149
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining EAP Forwarding Settings Ports use the Extensible Authentication Protocol (EAP) forwarding mechanism when 802.1x authentication is disabled. The Forwarding EAP Page allows the user packets. This is the default. 2. Define the EAP
  • D-Link 3100 24P | User Manual - Page 150
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Block Ciphers - Cipher Block Chaining (CBC) links encrypted text blocks. The Switch supports the 3DES EDE encryption code defined by The Switch possesses three possible ciphersuites for the SSL function, which are enabled by default. When
  • D-Link 3100 24P | User Manual - Page 151
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The SSL Configuration Settings Page contains the on the device. Disabled - Indicates SSL is disabled on the device. (This is the default value.) Ciphersuite Indicates the Ciphersuite. The possible field values are: RSA with RC4 128 MD5
  • D-Link 3100 24P | User Manual - Page 152
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Secure Shell Security Secure Shell permits network users User Account on the Switch, including specifying a password. This password is used to logon to the Switch device. This is the default value. Port (1-65535) Displays the port
  • D-Link 3100 24P | User Manual - Page 153
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3. Define the SSH global setting port number in the Port to authenticate communications between different applications. The following Encryption Algorithms are supported - 3DES-CBC - Supports a block size of 8 bytes (64 bits); its key size
  • D-Link 3100 24P | User Manual - Page 154
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual All algorithms are enabled by default. To enable SSH Algorithms: 1. Click Security > SSH > SSH Algorithm Settings. The SSH Algorithm Settings Page opens: Figure 5-90. SSH Algorithm Settings Page The SSH Algorithm
  • D-Link 3100 24P | User Manual - Page 155
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Application Authentication Settings Application Authentication permits network administrators to assign authentication methods for user authentication. For example, console users can be authenticated by Authentication List 1,
  • D-Link 3100 24P | User Manual - Page 156
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Authentication Server Hosts The Authentication Server is a remote device connected to the same network as the Client and Authenticator. Users the Radius port number defaults to 1812, TACACS+ port number defaults to 49. Timeout
  • D-Link 3100 24P | User Manual - Page 157
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3. Click .The Authentication Host properties are defined, and the device is updated.  To edit an authentication, click adjacent to the relevant IP Address on the list. The upper fields display the current values, which then can be
  • D-Link 3100 24P | User Manual - Page 158
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description are: RADIUS - User authentication occurs at the RADIUS server. TACACS+ - The user authentication occurs at the TACACS+ server. None - No user authentication occurs. Local - User authentication occurs at the device level
  • D-Link 3100 24P | User Manual - Page 159
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Enable Methods Network users must first login to the device on the Enable Method Lists Page. Access as non-administrative users is granted. The Enable Method Lists Page allows network mangers to assign user privileges using
  • D-Link 3100 24P | User Manual - Page 160
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Method 2 Description Indicates the second method used to authenticate the network user. The possible field values are: RADIUS - User authentication occurs at the RADIUS server. TACACS+ - The user authentication occurs at the TACACS
  • D-Link 3100 24P | User Manual - Page 161
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Local Enable Password The Configure Local Enable Password Page allows network administrators to configure the local enabled password. To define the network Local Enable password: 1. Click Security > Access Authentication
  • D-Link 3100 24P | User Manual - Page 162
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 6 MONITORING THE DEVICE This section contains information for view device and packet statistics as well as, viewing IGMP information and MAC address information. This section
  • D-Link 3100 24P | User Manual - Page 163
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Stacking Information The Stacking Information Page provides to the stacking members. Runtime version Indicates the software version running on the device. H/W version Displays the stacking member's hardware version. 149
  • D-Link 3100 24P | User Manual - Page 164
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing CPU Utilization The CPU Utilization Page contains information are: Utilization checked - Utilization information is enabled. This is the default value. Utilization unchecked - Utilization information is disabled. 2. Define the
  • D-Link 3100 24P | User Manual - Page 165
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Port Utilization The Port Utilization Page contains fields are: Utilization checked - Utilization information is enabled .This is the default value. Utilization unchecked - Utilization information is disabled. 2. Define the Unit
  • D-Link 3100 24P | User Manual - Page 166
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Packet Size Information The Packet Size Page displays packets received by the switch, arranged in seven groups and classed by size, to be viewed as either a line graph or a table. 1. Click Monitoring > Packet Size. The Packet Size
  • D-Link 3100 24P | User Manual - Page 167
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Received Packet Statistics The Received(RX) Page contains information about packets transmitted through device ports. To view received packet statistics: 1. Click Monitoring > Packets > Received(
  • D-Link 3100 24P | User Manual - Page 168
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 6. Define the Show/Hide field. 7. To view the graph as a table, click View Table. Viewing UMB_cast Packet Statistics The UMB_cast(RX) Page displays the number
  • D-Link 3100 24P | User Manual - Page 169
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 3. Click to load the defined parameters. To clear the Unit and Port fields: 1. Click . The fields are cleared. 2. Define the Time Interval and Record Number
  • D-Link 3100 24P | User Manual - Page 170
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Description Packets checked - Displays the total amount of transmitted packets. 2. Define the Unit and Port fields. 3. Click to load the defined parameters. To clear
  • D-Link 3100 24P | User Manual - Page 171
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing RADIUS Authenticated Session Statistics The RADIUS Authentication time intervals are: 15/30/60/no refresh. Server Displays the RADIUS server IP address. UDP Port Displays the UDP port through which the RADIUS session was
  • D-Link 3100 24P | User Manual - Page 172
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing ARP Table The Browse ARP Table Page provides information regarding ARP VLANs, including which IP address was mapped to what MAC address. To view the ARP table: 1. Click Monitoring > Browse ARP Table. The Browse ARP Table Page opens
  • D-Link 3100 24P | User Manual - Page 173
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing MLD Router Ports The Browse MLD Router MLD Router Port Page contains the following fields: Field Description VID Indicates the VLAN identification. Unit Indicates the stacking member for which the router ports information is
  • D-Link 3100 24P | User Manual - Page 174
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Router Ports The Browse Router Port Page Router Port Page contains the following fields: Field Description VID Indicates the VLAN identification. Unit Indicates the stacking member for which the router ports information
  • D-Link 3100 24P | User Manual - Page 175
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing Session Table The Browse Session Table Page displays information regarding device sessions which were initiated by system Users. To view session table information: 1. Click Monitoring > Browse Session Table. The Browse Session
  • D-Link 3100 24P | User Manual - Page 176
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing IGMP Group Information The IGMP Snooping Group Page contains vital IGMP group information, including the Multicast Group IP address and the corresponding MAC address through which the IGMP packets passed. 1. Click Monitoring >IGMP
  • D-Link 3100 24P | User Manual - Page 177
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing MLD Group Information The MLD Snooping Group Page contains vital MLD group information, including the Multicast Group IP address and the corresponding MAC address through which the MLD packets passed. 1. Click Monitoring > MLD
  • D-Link 3100 24P | User Manual - Page 178
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Dynamic and Static MAC Addresses Packets addressed to destinations stored in either the Static or Dynamic databases are immediately forwarded to the port. The MAC Address Table Page can be sorted by interface, VLAN, or MAC Address
  • D-Link 3100 24P | User Manual - Page 179
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 4. Click . - To view all entries, click - To clear static entries, click - To clear dynamic entries, click - To clear all entries, click - To scroll down the
  • D-Link 3100 24P | User Manual - Page 180
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Viewing System Log The System Log Page provides information about system logs, including information when the device was booted, how the ports are operating, when users functioning, but an operational problem has occurred. - Informational
  • D-Link 3100 24P | User Manual - Page 181
    and video remote monitoring Powered Devices are devices which receive power from the DGS-3100 series device power supplies, for example IP phones. Powered Devices are connected to the DGS-3100 series device via Ethernet ports. PoE is enabled only on the DGS-3100-24P and DGS-3100-48P devices. This
  • D-Link 3100 24P | User Manual - Page 182
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining PoE System Information The PoE Port Setting Page contains system PoE information for enabling PoE on the device, monitoring the current power usage, and enabling PoE traps. To enable PoE on the device: 1. Click PoE > PoE Port
  • D-Link 3100 24P | User Manual - Page 183
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Fields Status Description Class 2 - Indicates the power consumption circuit. 2. Define the Unit, From Port, To Port, PoE Enable and Power Limit fields. 3. Click . The system PoE parameters are defined, and the device is updated. 169
  • D-Link 3100 24P | User Manual - Page 184
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Displaying and Editing PoE System Information The PoE System Setting Page displays system PoE information on the device, monitoring the current power usage, and enabling PoE traps. To display system PoE information on the device: 1. Click
  • D-Link 3100 24P | User Manual - Page 185
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 8 DEFINING ACCESS PROFILE LISTS Access Control Lists (ACL) allow network managers to define classification actions and rules for specific ingress ports. Packets entering an ingress
  • D-Link 3100 24P | User Manual - Page 186
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual ACL Configuration Wizard The ACL Configuration Wizard Page ACL action will take place on packets to this IPv4 address. Service Type Defines the type of service. The possible values are: Any - Indicates ACL action will take place for packets
  • D-Link 3100 24P | User Manual - Page 187
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Fields Description UDPAll - Specifies a UDP Packets ACL is time-based. Range Name Selects the user-defined time range name to apply to the configured ACL. 2. Define the From, To, Service Type, Action, and Ports fields. To configure
  • D-Link 3100 24P | User Manual - Page 188
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Access Profile Lists This section contains the following topics:  Adding ACL Profiles  Defining Level 2 ACL  Defining Level 3 ACL Adding ACL Profiles The ACL Profile
  • D-Link 3100 24P | User Manual - Page 189
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 8-3 Add ACL Profile Page The Add ACL Profile Page contains the following fields: Field L2 ACL Description Defines the ACL profile Layer 2 protocols. The
  • D-Link 3100 24P | User Manual - Page 190
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Level 2 ACL If L2 ACL Tagged is selected, the page updates as follows: Figure 8-4 ACL Profile L2 ACL Tagged Page To define L2 MAC
  • D-Link 3100 24P | User Manual - Page 191
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The ACL Profile L2 ACL Tagged MAC Address the 802.1p field as an essential field to match. VLAN VID Sets the VLAN VID field as an essential field to match. 2. Define the 802.1p and VLAN VID fields. 3. Click . The ACL profile is added
  • D-Link 3100 24P | User Manual - Page 192
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click Figure 8-7 ACL Profile L2 ACL Tagged Ether Type Page . The ACL profile is added, and the device is updated. NOTE: A combination of one or
  • D-Link 3100 24P | User Manual - Page 193
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L2 ACL Untagged is selected, the page updates as follows (without the 802.1Q VLAN field): Figure 8-8 ACL Profile L2 ACL Untagged Page Defining Level 3 ACL If L3 ACL ICMP is selected, the page updates as follows: Figure 8-9 Add ACL
  • D-Link 3100 24P | User Manual - Page 194
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual This option defines whether or not the DSCP field is checked for a match. 1. Click the IPv4 DSCP button. The ACL Profile L3 ACL ICMP IPv4
  • D-Link 3100 24P | User Manual - Page 195
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The ACL Profile L3 ACL ICMP IPv4 Address Page contains the following fields: Field Description Source IP Mask Defines the range of source IP addresses, relevant to the ACL rules. (0=ignore, 1=check). For example, to set 176.212.XX.XX,
  • D-Link 3100 24P | User Manual - Page 196
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L3 ACL IGMP is selected, the page updates as follows: Figure 8-13 ACL Profile L3 IGMP Page 1. Click the IGMP button. The ACL Profile
  • D-Link 3100 24P | User Manual - Page 197
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L3 ACL TCP is selected, the page updates as follows: Figure 8-15 ACL Profile L3 TCP Page To define L3 TCP Port ACL profile: 1.
  • D-Link 3100 24P | User Manual - Page 198
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual The ACL Profile L3 TCP Port Page contains the following fields: Field Description Source Port Mask Defines the range of source Ports relevant to the
  • D-Link 3100 24P | User Manual - Page 199
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual If L3 ACL UDP is selected, the page updates as follows: Figure 8-18 ACL Profile L3 UDP Page 1. Click the UDP Port button. The ACL
  • D-Link 3100 24P | User Manual - Page 200
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Source Port Mask Description Defines the range of source Ports relevant to the ACL rules. (0=ignore, 1=check). For example, to set 0 - 15, set mask of F. Destination Port Mask Defines the range of destination IP addresses,
  • D-Link 3100 24P | User Manual - Page 201
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Access Rules Lists The following conditions can be defined as Access Rules: Filter Source Port IP Address and Wildcard Mask Description Filters the packets by the Source port IP address and wildcard mask. Destination Port IP
  • D-Link 3100 24P | User Manual - Page 202
    To change ACL rules: 1. Click DGS-3100 Series Gigabit Stackable Managed Switch User Manual . The Add Access Rule Page opens: Figure 8-21 Add Access Rule Page (IP based ACL) The Add Access Rule Page contains the following fields: Field Description Profile ID Displays the Profile ID to which
  • D-Link 3100 24P | User Manual - Page 203
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Field Range Name Description Selects the user-defined time range name to apply to the access rule. 2. Define the Rule Detail fields. 3. Click . The rule is changed, and the device is updated.
  • D-Link 3100 24P | User Manual - Page 204
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Finding ACL ACL rule ID number. Profile Type Indicates if the profile is IP or Ethernet Summary Displays the access rule. Action Displays the action details: 1. Click the Access ID (linked number). The Rule Detail Page opens: 190
  • D-Link 3100 24P | User Manual - Page 205
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Figure 8-23 Rule Detail Page The Rule Detail Access ID Type Displays the profile type (can be MAC based or IP based). VLAN Name Defines the user-defined VLAN name. Destination MAC Address Matches the destination MAC address to which
  • D-Link 3100 24P | User Manual - Page 206
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Define the Rule Detail fields. 3. Click . The rule is defined, and the device is update 192
  • D-Link 3100 24P | User Manual - Page 207
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining Time Ranges Time-based ACLs allow users to define Access Control Lists based on time periods. The Time Range Setting Page defines a time range, which can be applied to an ACL rule.
  • D-Link 3100 24P | User Manual - Page 208
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Click . A confirmation window is displayed . 3. Click . modified, and the device is updated Notes about 'IP' and 'MAC' Based ACLs in the DGS-3100 Series ACLs can be configured in DGS-3100 series via the WEB GUI in two ways: through
  • D-Link 3100 24P | User Manual - Page 209
    DGS-3100 Series Gigabit Stackable Managed Switch User Manual - Add L3 Access Profile with the desired fields. - Go to 'Access Rule List' page, create rules for both profiles and apply it on the same port(s) /LAG(s). Now you have on the port(s) /LAG(s) IP Based ACL and MAC Based ACL. NOTE: Adding
  • D-Link 3100 24P | User Manual - Page 210
    Switch User Manual Notes about ACLs capacity in the DGS-3100 Series  The user can create up to 15 Access Profiles.  The user can configure up to 240 Access IDs, each Access ID is unique i.e. the same Access ID can't be created from two different Access Profiles.  The maximum capacity of DGS-3100
  • D-Link 3100 24P | User Manual - Page 211
    of DLink and its suppliers under this Limited Warranty will be, at D-Link's option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link's functional specifications for the Software or to refund the portion of the actual purchase price paid
  • D-Link 3100 24P | User Manual - Page 212
    software, firmware or other products or services provided by anyone other than DLink; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT user
  • D-Link 3100 24P | User Manual - Page 213
    Product Registration Register your D-Link product online at http://support.dlink.com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. 199
  • D-Link 3100 24P | User Manual - Page 214
    D-Link Service Link upon return to DLink of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund. Limited Software Warranty: D-Link warrants that the software
  • D-Link 3100 24P | User Manual - Page 215
    Link. The license granted respecting any Software for which a refund is given automatically terminates. What You Must Do For Warranty Service: Registration Card. The Registration Card provided at the back of this manual Authorized D-Link Service Office with all shipping costs prepaid. DLink may
  • D-Link 3100 24P | User Manual - Page 216
    covered in the operating manual for the product, and normal maintenance. Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage. Any hardware, software, firmware or other products or services provided by anyone other than D-Link. Disclaimer of Other
  • D-Link 3100 24P | User Manual - Page 217
    Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link , or adaptation without permission from DLink Corporation/D-Link Systems Inc., as stipulated by used in accordance with this manual, may cause harmful interference to
  • D-Link 3100 24P | User Manual - Page 218
    TECHNICAL SUPPORT Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the service period, and warranty confirmation service, during the
  • D-Link 3100 24P | User Manual - Page 219
    Support You can find software updates and user documentation on the D-Link websites. If you require product support, we encourage you to browse our FAQ section on the Web Site before contacting the Support line. We have many FAQ's which we hope will provide you a speedy resolution for your problem
  • D-Link 3100 24P | User Manual - Page 220
    von D-Link. D-Link bietet kostenfreie technische Unterstützung für Kunden innerhalb Deutschlands, Österreichs, der Schweiz und Osteuropas. Unsere Kunden können technische Unterstützung über unsere Website, per E-Mail oder telefonisch anfordern. Web: http://www.dlink.de E-Mail: [email protected]
  • D-Link 3100 24P | User Manual - Page 221
    et les logiciels les plus récents sur le site web DLink. Vous pouvez contacter le service technique de D-Link par notre site internet ou par téléphone. Support technique destiné aux clients établis en France: Assistance technique D-Link par téléphone : 0820 0803 03 N° INDIGO - 0,12€ TTC/min* *Prix
  • D-Link 3100 24P | User Manual - Page 222
    para clientes residentes en España durante el periodo de garantía del producto. Asistencia Técnica de D-Link por teléfono: +34 902 30 45 45 Lunes a Viernes de 9:00 a 14:00 y de 15:00 a 18:00 Asistencia Técnica de D-Link a través de Internet: http://www.dlink.es/support/ e-mail: [email protected] 208
  • D-Link 3100 24P | User Manual - Page 223
    sono disponibili sul sito D-Link. Supporto tecnico per i clienti residenti in Italia D-Link Mediterraneo S.r.L. Via N. Bonnet 6/B 20154 Milano Supporto Tecnico dal lunedì al venerdì dalle ore 9.00 alle ore 19.00 con orario continuato Telefono: 199 400057 URL : http://www.dlink.it/supporto.html Email
  • D-Link 3100 24P | User Manual - Page 224
    find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within Benelux for the duration of the warranty period on this product. Benelux customers can contact D-Link technical support through our website, or by phone. Tech Support for
  • D-Link 3100 24P | User Manual - Page 225
    okresie gwarancyjnym produktu. Klienci z Polski mogą się kontaktować z działem pomocy technicznej firmy D-Link za pośrednictwem Internetu lub telefonicznie. Telefoniczna pomoc techniczna firmy D-Link: 0 801 022 021 Pomoc techniczna firmy D-Link świadczona przez Internet: URL: http://www.dlink.pl 211
  • D-Link 3100 24P | User Manual - Page 226
    verze software a uživatelských příruček najdete na webové stránce firmy D-Link. D-Link poskytuje svým zákazníkům bezplatnou technickou podporu Zákazníci mohou kontaktovat oddělení technické podpory přes webové stránky, mailem nebo telefonicky Web: http://www.dlink.cz/suppport/ E-mail: support@dlink
  • D-Link 3100 24P | User Manual - Page 227
    hétfőtől-csütörtökig 9.00 - 16.00 óráig és pénteken 9.00 - 14.00 óráig kérhet a (1) 461-3001 telefonszámon vagy a [email protected] emailcímen. Magyarországi technikai támogatás : D-Link Magyarország 1074 Budapest, Alsóerdősor u. 6. - R70 Irodaház 1 em. Tel. : 06 1 461-3001 Fax : 06 1 461-3004 email
  • D-Link 3100 24P | User Manual - Page 228
    . D-Link tilbyr sine kunder gratis teknisk support under produktets garantitid. Kunder kan kontakte D-Links teknisk support via våre hjemmesider, eller på tlf. Teknisk Support: D-Link Teknisk telefon Support: 800 10 610 (Hverdager 08:00-20:00) D-Link Teknisk Support over Internett: http://www.dlink
  • D-Link 3100 24P | User Manual - Page 229
    Support Du finder software opdateringer og brugerdokumentation på D-Link's hjemmeside. D-Link tilbyder gratis teknisk support til kunder i Danmark i hele produktets garantiperiode. Danske kunder kan kontakte D-Link's tekniske support via vores hjemmeside eller telefonisk. D-Link teknisk support
  • D-Link 3100 24P | User Manual - Page 230
    Teknistä tukea asiakkaille Suomessa: D-Link tarjoaa teknistä tukea asiakkailleen. Tuotteen takuun voimassaoloajan. Tekninen tuki palvelee seuraavasti: Arkisin klo. 9 - 21 numerosta 0800-114 677 Internetin kautta Ajurit ja lisätietoja tuotteista. http://www.dlink.fi Sähköpostin kautta voit myös tehdä
  • D-Link 3100 24P | User Manual - Page 231
    annan användarinformation. D-Link tillhandahåller teknisk support till kunder i Sverige under hela garantitiden för denna produkt. Teknisk Support för kunder i Sverige: D-Link Teknisk Support via telefon: 0770-33 00 35 Vardagar 08.00-20.00 D-Link Teknisk Support via Internet: http://www.dlink.se 217
  • D-Link 3100 24P | User Manual - Page 232
    Suporte Técnico Você pode encontrar atualizações de software e documentação de utilizador no site de D-Link Portugal http://www.dlink.pt. A D-Link fornece suporte técnico gratuito para clientes no Portugal durante o período de vigência de garantia deste produto. Suporte Técnico para clientes no
  • D-Link 3100 24P | User Manual - Page 233
    software updates D-Link Η D-Link D-Link : Τηλ: 210 86 11 114 Φαξ: 210 86 53 172 09:00-17:00) e-mail: [email protected] D-Link μέσω Internet: http://www.dlink.gr ftp://ftp.dlink.it 219
  • D-Link 3100 24P | User Manual - Page 234
    You can find software updates and user documentation on the D-Link website. Tech Support for customers in Australia: Tel: 1300-766-868 Monday to Friday 8:00am to 8:00pm EST Saturday 9:00am to 1:00pm EST http://www.dlink.com.au e-mail: [email protected] India: Tel: 1800-222-002 Monday
  • D-Link 3100 24P | User Manual - Page 235
    You can find software updates and user documentation on the D-Link website. Tech Support for customers in Egypt: Tel: +202-2919035 or +202-2919047 Sunday to Thursday 9:00am to 5:00pm http://support.dlink-me.com e-mail: [email protected] Iran: Tel: +98-21-88822613 Sunday to Thursday 9:00am
  • D-Link 3100 24P | User Manual - Page 236
    D-Link. D-Link D-Link D-Link: +495-744-00-99 http://www.dlink.ru e-mail: [email protected] 222
  • D-Link 3100 24P | User Manual - Page 237
    ón de sus clientes, especificaciones, documentación y software mas reciente a través de nuestro Sitio Web www.dlinkla.com El servicio de soporte técnico tiene presencia en numerosos países de la Región Latino América, y presta asistencia gratuita a todos los clientes de D-Link, en forma telefónica
  • D-Link 3100 24P | User Manual - Page 238
    Suporte Técnico Você pode encontrar atualizações de software e documentação de usuário no site da D-Link Brasil www.dlinkbrasil.com.br. A D-Link fornece suporte técnico gratuito para clientes no Brasil durante o período de vigência da garantia deste produto. Suporte Técnico para clientes no Brasil:
  • D-Link 3100 24P | User Manual - Page 239
    D-Link d e JOL̨ᝄ f  D-Link j඄ɓЇ඄ʞd e   ၣ१jIUUQXXXEMJOLDPNUX ཥɿඉ΁jETTRB@TFSWJDF!EMJOLDPNUX dሗਞϽ%-JOL f  e d j IUUQXXXEMJOLDPNUX j f 225
  • D-Link 3100 24P | User Manual - Page 240
    Teknis Update perangkat lunak dan dokumentasi pengguna dapat diperoleh pada situs web D-Link. Dukungan Teknis untuk pelanggan: Dukungan Teknis D-Link melalui telepon: Tel: +62-21-5731610 Dukungan Teknis D-Link melalui Internet: Email : [email protected] Website : http://support.dlink.co.id 226
  • D-Link 3100 24P | User Manual - Page 241
     术 ˕ܵ D-Link 36 B 座 26F 02-05 100013 8008296688/ (028)66052968 028)85176948 36 B 座 26F 02-05 100013 010) 58257789 010) 58257790 网址：http://www.dlink.com.cn 227
  • D-Link 3100 24P | User Manual - Page 242
    dlink.no Poland Budynek Aurum ul. Waliców 11 00-851 Warszawa, Poland TEL: +48 (0) 22 583 92 75 FAX: +48 (0) 22 583 92 76 URL: www.dlink -1868 URL: www.dlink.com.au India D-Link House, Plot No.5, dlink.ru Japan K.K. Level 6 Konan YK Building, Konan 24-12 Minato-Ku Tokyo 108-0075, Japan URL: www.dlink
  • D-Link 3100 24P | User Manual - Page 243
    's name Telephone Answers to the following questions help us to support your product: 1. Where and how will the product primarily be use ? XNS/IPX TCP/IP DECnet Others 4. What network operating system(s) does your organization use ? D-Link LANsmart Novell NetWare NetWare Lite
  • D-Link 3100 24P | User Manual - Page 244
    230
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
D-Link
™
DGS-3100 SERIES
GIGABIT STACKABLE MANAGED SWITCH
User Manual
V2.30