D-Link DCS-3415 User Manual - Page 40

Camera from the Internet. For example, when the HTTP port is set to 80 and the secondary HTTP port

Get D-Link DCS-3415 PDF manuals and user guides
UPC - 790069313752
View all D-Link DCS-3415 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Section 4 - Configuration Enabling UPnP port forwarding allows the Network Camera to open secondary HTTP port on the router, not HTTP port, meaning that you have to add the secondary HTTP port number behind the Network Camera's public address in order to access the Network Camera from the Internet. For example, when the HTTP port is set to 80 and the secondary HTTP port is set to 8080, refer to the list below for the Network Camera's IP address. From the Internet http://203.67.124.123:8080 In a local area network http://192.168.4.160 or http://192.168.4.160:8080 If the PPPoE settings are incorrectly configured or the Internet access is not working, restore the Network Camera to factory default. After the Network Camera is reset to factory default, it is accessible in a local area network. Enable UPnP Port Enables the camera to add the port forwarding entry into the router automatically when this option is enabled. Forwarding: PPPoE Settings: Enable this setting if your ISP (DSL service) is using PPPoE. You may already have both Username and Password given by your ISP, or you may check with your ISP. The Connect Status will be determined automatically by the system. HTTP: You may configure two HTTP ports for your camera. HTTP ports allow you to connect to the camera via a standard web browser. These ports can be set to a number other than the default TCP ports 80 and 8080. A corresponding port must be opened on the router. For example, if the port is changed to 1010, users must type in the web browser "http://192.168.0.100:1010" instead of "http://192.168.0.100". Authentication: Authentication: Choose either Basic where the password is not encrypted, or Digest where the password is encrypted during the transmission to the web server. Note: Ensure to restart your browser, if you select Digest mode. Basic authentication: When selected, the password is sent in plain text format; there can be potential risks of being intercepted. Digest authentication: When selected, user credentials are encrypted in MD5 algorithm and thus provide better protection against unauthorized accesses. HTTP Port: The default value is 80. D-Link DCS-3415 User Manual 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
40
D-Link DCS-3415 User Manual
Section 4 - Configuration
Enable UPnP Port
Forwarding:
PPPoE Settings:
HTTP:
Authentication:
HTTP Port:
Enabling UPnP port forwarding allows the Network Camera to open secondary HTTP port on the router, not HTTP port, meaning
that you have to add the secondary HTTP port number behind the Network Camera’s public address in order to access the Network
Camera from the Internet. For example, when the HTTP port is set to 80 and the secondary HTTP port is set to 8080, refer to the
list below for the Network Camera’s IP address.
From the Internet
In a local area network
If the PPPoE settings are incorrectly configured or the Internet access is not working, restore the Network Camera to factory default.
After the Network Camera is reset to factory default, it is accessible in a local area network.
Enables the camera to add the port forwarding entry into the router automatically when this option is enabled.
Enable this setting if your ISP (DSL service) is using PPPoE. You may already have both
Username
and
Password
given by your ISP, or
you may check with your ISP. The
Connect Status
will be determined automatically by the system.
You may configure two HTTP ports for your camera. HTTP ports allow you to connect to the camera via a standard web browser. These ports
can be set to a number other than the default TCP ports 80 and 8080. A corresponding port must be opened on the router. For example,
if the port is changed to 1010, users must type in the web browser “http://19±.168.0.100:1010” instead of “http://19±.168.0.100”.
Authentication
: Choose either
Basic
where the password is not encrypted, or
Digest
where the password is encrypted during the
transmission to the web server.
Note:
Ensure to restart your browser, if you select
Digest
mode.
Basic authentication:
When selected, the password is sent in plain text format; there can be potential risks of being intercepted.
Digest authentication:
When selected, user credentials are encrypted in MD5 algorithm and thus provide better protection against
unauthorized accesses.
The default value is 80.