Home » D-Link Manuals » Networking » D-Link DFL-800-AV-12 » Manual Viewer

D-Link DFL-800-AV-12 User Manual - Page 105

The Designated Router, Neighbors, Aggregates

View all D-Link DFL-800-AV-12 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

4.4.2. OSPF Chapter 4. Routing ASBRs Backbone Areas Stub Areas Transit Areas to which they have an interface. Routers that exchange routing information with routers in other Autonomous Systems are called Autonomous System Boundary Router (ASBRs). They advertise externally learned routes throughout the Autonomous System. All OSPF networks need to have at least the backbone area, that is the area with ID 0. This is the area that all other areas should be connected to, and the backbone make sure to distribute routing information between the connected areas. When an area is not directly connected to the backbone it needs a virtual link to it. Stub areas are areas through which or into which AS external advertisements are not flooded. When an area is configured as a stub area, the router will automatically advertises a default route so that routers in the stub area can reach destinations outside the area. Transit areas are used to pass traffic from a area that is not directly connect to the backbone area. The Designated Router Each OSPF broadcast network has a designated router and a backup designated router. The routers uses OSPF hello protocol to elect the DR and BDR for the network based on the priorities advertised by all the routers. If there already are a DR on the network, the router will accept that one, regardless of its own router priority. Neighbors Routers that are in the same area become neighbors in that area. Neighbors are elected via the Hello protocol. Hello packets are sent periodically out of each interface using IP multicast. Routers become neighbors as soon as they see themselves listed in the neighbor's Hello packet. This way, a two way communication is guaranteed. The following Neighbor States are defined: Down Init 2-Way ExStart Exchange Loading Full This is the initial stat of the neighbor relationship. When a HELLO packet is received from a neighbor, but does NOT include the Router ID of the firewall in it, the neighbor will be placed in Init state. As soon as the neighbor in question receives a HELLO packet it will know the sending routers Router ID and will send a HELLO packet with that included. The state of the neighbors will change to 2-way state. In this state the communication between the router and the neighbor is bi-directional. On Point-to-Point and Point-to-Multipoint interfaces, the state will be changed to Full. On Broadcast interfaces, only the DR/BDR will advance to Fullstate with their neighbors, all the remaining neighbors will remain in the 2-Way state. Preparing to build adjacency. Routers are exchanging Data Descriptors. Routers are exchanging LSAs. This is the normal state of an adjacency between a router and the DR/BDR. Aggregates OSPF Aggregation is used to combine groups of routes with common addresses into a single entry 105

Section	Page
User Manual	3
Table of Contents	4
Preface	12
Chapter 1. Product Overview	14
1.1. About D-Link NetDefendOS	14
1.2. NetDefendOS Architecture	16
1.2.1. State-based Architecture	16
1.2.2. NetDefendOS Building Blocks	16
1.2.3. Basic Packet Flow	17
1.3. NetDefendOS State Engine Packet Flow	19
Chapter 2. Management and Maintenance	23
2.1. Managing NetDefendOS	23
2.1.1. Overview	23
2.1.2. Default Administrator Accounts	23
2.1.3. The CLI	24
2.1.4. The WebUI	26
2.1.5. Working with Configurations	29
2.2. Events and Logging	35
2.2.1. Overview	35
2.2.2. Event Messages	35
2.2.3. Event Message Distribution	35
2.2.3.1. Logging to Syslog Hosts	36
2.2.3.2. SNMP Traps	37
2.3. RADIUS Accounting	39
2.3.1. Overview	39
2.3.2. RADIUS Accounting Messages	39
2.3.3. Interim Accounting Messages	41
2.3.4. Activating RADIUS Accounting	41
2.3.5. RADIUS Accounting Security	41
2.3.6. RADIUS Accounting and High Availability	41
2.3.7. Handling Unresponsive Servers	42
2.3.8. Accounting and System Shutdowns	42
2.3.9. Limitations with NAT	42
2.4. Monitoring	43
2.4.1. SNMP Monitoring	43
2.5. Maintenance	45
2.5.1. Auto-Update Mechanism	45
2.5.2. Configuration Backup and Restore	45
2.5.3. Resetting to Factory Defaults	45
Chapter 3. Fundamentals	48
3.1. The Address Book	48
3.1.1. Overview	48
3.1.2. IP Addresses	48
3.1.3. Ethernet Addresses	50
3.1.4. Address Groups	51
3.1.5. Auto-Generated Address Objects	51
3.2. Services	52
3.2.1. Overview	52
3.2.2. TCP and UDP Based Services	53
3.2.3. ICMP Services	55
3.2.4. Custom IP Protocol Services	55
3.3. Interfaces	57
3.3.1. Overview	57
3.3.2. Ethernet	58
3.3.3. VLAN	60
3.3.4. PPPoE	61
3.3.4.1. Overview of PPP	61
3.3.4.2. PPPoE Client Configuration	62
3.3.5. GRE Tunnels	63
3.3.6. Interface Groups	66
3.4. ARP	68
3.4.1. Overview	68
3.4.2. ARP in NetDefendOS	68
3.4.3. ARP Cache	68
3.4.4. Static and Published ARP Entries	69
3.4.5. Advanced ARP Settings	71
3.5. The IP Rule Set	73
3.5.1. Security Policies	73
3.5.2. IP Rule Evaluation	74
3.5.3. IP Rule Actions	75
3.5.4. Editing IP rule set Entries	76
3.6. Schedules	77
3.7. X.509 Certificates	79
3.7.1. Overview	79
3.7.2. X.509 Certificates in NetDefendOS	80
3.8. Setting Date and Time	82
3.8.1. General Date and Time Settings	82
3.8.2. Time Servers	83
3.9. DNS Lookup	87
Chapter 4. Routing	89
4.1. Overview	89
4.2. Static Routing	90
4.2.1. Basic Principles of Routing	90
4.2.2. Static Routing	91
4.2.3. Route Failover	94
4.2.4. Proxy ARP	96
4.3. Policy-based Routing	98
4.3.1. Overview	98
4.3.2. Policy-based Routing Tables	98
4.3.3. Policy-based Routing Rules	98
4.3.4. Policy-based Routing Table Selection	99
4.3.5. The Ordering parameter	99
4.4. Dynamic Routing	103
4.4.1. Dynamic Routing overview	103
4.4.2. OSPF	104
4.4.3. Dynamic Routing Policy	107
4.5. Multicast Routing	110
4.5.1. Overview	110
4.5.2. Multicast Forwarding using the SAT Multiplex Rule	110
4.5.2.1. Multicast Forwarding - No Address Translation	111
4.5.2.2. Multicast Forwarding - Address Translation Scenario	112
4.5.3. IGMP Configuration	114
4.5.3.1. IGMP Rules Configuration - No Address Translation	115
4.5.3.2. IGMP Rules Configuration - Address Translation	116
4.6. Transparent Mode	119
4.6.1. Overview of Transparent Mode	119
4.6.2. Comparison with Routing mode	119
4.6.3. Transparent Mode Implementation	119
4.6.4. Enabling Transparent Mode	120
4.6.5. High Availability with Transparent Mode	120
4.6.6. Transparent Mode Scenarios	120
Chapter 5. DHCP Services	127
5.1. Overview	127
5.2. DHCP Servers	128
5.3. Static DHCP Assignment	130
5.4. DHCP Relaying	131
5.5. IP Pools	132
Chapter 6. Security Mechanisms	135
6.1. Access Rules	135
6.1.1. Introduction	135
6.1.2. IP spoofing	135
6.1.3. Access Rule Settings	136
6.2. Application Layer Gateways	138
6.2.1. Overview	138
6.2.2. HTTP	139
6.2.3. FTP	140
6.2.4. TFTP	145
6.2.5. SMTP	146
6.2.5.1. DNSBL SPAM Filtering	147
6.2.6. POP3	151
6.2.7. SIP	152
6.2.8. H.323	155
6.3. Web Content Filtering	169
6.3.1. Overview	169
6.3.2. Active Content Handling	169
6.3.3. Static Content Filtering	170
6.3.4. Dynamic Web Content Filtering	172
6.3.4.1. Content Filtering Categories	176
6.4. Anti-Virus Scanning	183
6.4.1. Overview	183
6.4.2. Implementation	183
6.4.3. Activating Anti-Virus Scanning	184
6.4.4. The Signature Database	184
6.4.5. Subscribing to the D-Link Anti-Virus Service	184
6.4.6. Anti-Virus Options	184
6.5. Intrusion Detection and Prevention	188
6.5.1. Overview	188
6.5.2. IDP Availability in D-Link Models	188
6.5.3. IDP Rules	190
6.5.4. Insertion/Evasion Attack Prevention	191
6.5.5. IDP Pattern Matching	192
6.5.6. IDP Signature Groups	192
6.5.7. IDP Actions	194
6.5.8. SMTP Log Receiver for IDP Events	194
6.6. Denial-Of-Service (DoS) Attacks	198
6.6.1. Overview	198
6.6.2. DoS Attack Mechanisms	198
6.6.3. Ping of Death and Jolt Attacks	198
6.6.4. Fragmentation overlap attacks: Teardrop, Bonk, Boink and Nestea	199
6.6.5. The Land and LaTierra attacks	199
6.6.6. The WinNuke attack	199
6.6.7. Amplification attacks: Smurf, Papasmurf, Fraggle	200
6.6.8. TCP SYN Flood Attacks	201
6.6.9. The Jolt2 Attack	201
6.6.10. Distributed DoS Attacks	201
6.7. Blacklisting Hosts and Networks	202
Chapter 7. Address Translation	204
7.1. Dynamic Network Address Translation	204
7.2. NAT Pools	207
7.3. Static Address Translation	210
7.3.1. Translation of a Single IP Address (1:1)	210
7.3.2. Translation of Multiple IP Addresses (M:N)	213
7.3.3. All-to-One Mappings (N:1)	215
7.3.4. Port Translation	216
7.3.5. Protocols handled by SAT	216
7.3.6. Multiple SAT rule matches	217
7.3.7. SAT and FwdFast Rules	217
Chapter 8. User Authentication	220
8.1. Overview	220
8.2. Authentication Setup	221
8.2.1. Setup Summary	221
8.2.2. The Local Database	221
8.2.3. External Authentication Servers	221
8.2.4. Authentication Rules	222
8.2.5. Authentication Processing	223
8.2.6. HTTP Authentication	223
Chapter 9. VPN	229
9.1. Overview	229
9.1.1. The Need for VPNs	229
9.1.2. VPN Encryption	229
9.1.3. VPN Planning	229
9.1.4. Key Distribution	230
9.2. VPN Quickstart Guide	231
9.2.1. IPsec LAN to LAN with Pre-shared Keys	231
9.2.2. IPsec Roaming Clients with Pre-shared Keys	232
9.2.3. IPsec Roaming Clients with Certificates	234
9.2.4. L2TP Roaming Clients with Pre-Shared Keys	234
9.2.5. L2TP Roaming Clients with Certificates	236
9.2.6. PPTP Roaming Clients	236
9.2.7. VPN Troubleshooting	237
9.3. IPsec	240
9.3.1. Overview	240
9.3.2. Internet Key Exchange (IKE)	240
9.3.3. IKE Authentication	245
9.3.4. IPsec Protocols (ESP/AH)	247
9.3.5. NAT Traversal	248
9.3.6. Proposal Lists	249
9.3.7. Pre-shared Keys	250
9.3.8. Identification Lists	251
9.4. IPsec Tunnels	253
9.4.1. Overview	253
9.4.2. LAN to LAN Tunnels with Pre-shared Keys	253
9.4.3. Roaming Clients	253
9.4.3.1. PSK based client tunnels	254
9.4.3.2. Self-signed Certificate based client tunnels	255
9.4.3.3. CA Server issued Certificates based client tunnels	256
9.4.3.4. Using Config Mode	257
9.4.4. Fetching CRLs from an alternate LDAP server	259
9.5. PPTP/L2TP	260
9.5.1. PPTP	260
9.5.2. L2TP	261
Chapter 10. Traffic Management	267
10.1. Traffic Shaping	267
10.1.1. Introduction	267
10.1.2. Traffic Shaping in NetDefendOS	268
10.1.3. Simple Bandwidth Limiting	269
10.1.4. Limiting Bandwidth in Both Directions	270
10.1.5. Creating Differentiated Limits with Chains	271
10.1.6. Precedences	272
10.1.7. Guarantees	274
10.1.8. Differentiated Guarantees	274
10.1.9. Groups	275
10.1.10. Recommendations	276
10.1.11. A Summary of Traffic Shaping	277
10.2. Threshold Rules	279
10.2.1. Overview	279
10.2.2. Connection Rate/Total Connection Limiting	279
10.2.3. Grouping	279
10.2.4. Rule Actions	279
10.2.5. Multiple Triggered Actions	280
10.2.6. Exempted Connections	280
10.2.7. Threshold Rules and ZoneDefense	280
10.2.8. Threshold Rule Blacklisting	280
10.3. Server Load Balancing	281
10.3.1. Overview	281
10.3.2. Identifying the Servers	282
10.3.3. The Load Distribution Mode	282
10.3.4. The Distribution Algorithm	282
10.3.5. Server Health Monitoring	284
10.3.6. SLB_SAT Rules	284
Chapter 11. High Availability	289
11.1. Overview	289
11.2. High Availability Mechanisms	291
11.3. High Availability Setup	293
11.3.1. Hardware Setup	293
11.3.2. NetDefendOS Setup	294
11.3.3. Verifying Cluster Functioning	294
11.4. High Availability Issues	296
Chapter 12. ZoneDefense	298
12.1. Overview	298
12.2. ZoneDefense Switches	299
12.3. ZoneDefense Operation	300
12.3.1. SNMP	300
12.3.2. Threshold Rules	300
12.3.3. Manual Blocking and Exclude Lists	300
12.3.4. Limitations	302
Chapter 13. Advanced Settings	304
13.1. IP Level Settings	304
13.2. TCP Level Settings	307
13.3. ICMP Level Settings	311
13.4. ARP Settings	312
13.5. Stateful Inspection Settings	314
13.6. Connection Timeouts	316
13.7. Size Limits by Protocol	318
13.8. Fragmentation Settings	320
13.9. Local Fragment Reassembly Settings	324
13.10. DHCP Settings	325
13.11. DHCPRelay Settings	326
13.12. DHCPServer Settings	327
13.13. IPsec Settings	328
13.14. Logging Settings	330
13.15. Time Synchronization Settings	331
13.16. PPP Settings	333
13.17. Hardware Monitor Settings	334
13.18. Packet Re-assembly Settings	335
13.19. Miscellaneous Settings	336
Appendix A. Subscribing to Security Updates	338
Appendix B. IDP Signature Groups	340
Appendix C. Checked MIME filetypes	344
Appendix D. The OSI Framework	348
Appendix E. D-Link worldwide offices	349

Match case Limit results 1 per page

to which they have an interface.

ASBRs

Routers that exchange routing information with routers in other Autonomous

Systems are called Autonomous System Boundary Router (ASBRs). They

advertise externally learned routes throughout the Autonomous System.

Backbone Areas

All OSPF networks need to have at least the backbone area, that is the area

with ID 0. This is the area that all other areas should be connected to, and the

backbone make sure to distribute routing information between the connected

areas. When an area is not directly connected to the backbone it needs a

virtual link to it.

Stub Areas

Stub areas are areas through which or into which AS external advertisements

are not flooded. When an area is configured as a stub area, the router will

automatically advertises a default route so that routers in the stub area can

reach destinations outside the area.

Transit Areas

Transit areas are used to pass traffic from a area that is not directly connect

to the backbone area.

The Designated Router

Each OSPF broadcast network has a designated router and a backup designated router. The routers

uses OSPF hello protocol to elect the DR and BDR for the network based on the priorities

advertised by all the routers. If there already are a DR on the network, the router will accept that

one, regardless of its own router priority.

Neighbors

Routers that are in the same area become neighbors in that area. Neighbors are elected via the Hello

protocol. Hello packets are sent periodically out of each interface using IP multicast. Routers

become neighbors as soon as they see themselves listed in the neighbor's Hello packet. This way, a

two way communication is guaranteed.

The following

Neighbor States

are defined:

Down

This is the initial stat of the neighbor relationship.

Init

When a HELLO packet is received from a neighbor, but does NOT include the Router

ID of the firewall in it, the neighbor will be placed in Init state. As soon as the

neighbor in question receives a HELLO packet it will know the sending routers

Router ID and will send a HELLO packet with that included. The state of the

neighbors will change to

2-way

state.

2-Way

In this state the communication between the router and the neighbor is bi-directional.

On Point-to-Point and Point-to-Multipoint interfaces, the state will be changed to

Full

. On Broadcast interfaces, only the DR/BDR will advance to

Full

state with their

neighbors, all the remaining neighbors will remain in the 2-Way state.

ExStart

Preparing to build adjacency.

Exchange

Routers are exchanging Data Descriptors.

Routers are exchanging LSAs.

Full

This is the normal state of an adjacency between a router and the DR/BDR.

Aggregates

OSPF Aggregation is used to combine groups of routes with common addresses into a single entry

4.4.2. OSPF

Chapter 4. Routing

105