Home » D-Link Manuals » Networking » D-Link DFL-800-AV-12 » Manual Viewer

D-Link DFL-800-AV-12 User Manual - Page 261

L2TP, Interface=l2tp_ipsec IP=wan_ip IPPool=L2TP_Pool TunnelProtocol=L2TP

View all D-Link DFL-800-AV-12 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 261 highlights

9.5.2. L2TP Chapter 9. VPN gw-world:/> add Interface L2TPServer MyPPTPServer ServerIP=lan_ip Interface=any IP=wan_ip IPPool=pp2p_Pool TunnelProtocol=PPTP AllowedRoutes=all-nets Web Interface 1. Go to Interfaces > L2TP Servers > Add > L2TPServer 2. Enter a name for the PPTP Server eg. MyPPTPServer. 3. Now enter: • Inner IP Address: lan_ip • Tunnel Protocol: PPTP • Outer Interface Filter: any • Outer Server IP: wan_ip 4. Under the PPP Parameters tab, select pptp_Pool in the IP Pool control 5. Under the Add Route tab, select all_nets from Allowed Networks 6. Click OK Use User Authentication Rules is enabled as default. To be able to authenticate the users using the PPTP tunnel you also need to configure authentication rules, which will not be covered in this example. 9.5.2. L2TP Layer 2 Tunneling protocol (L2TP) is an IETF open standard that overcomes many of the problems of PPTP. Its design is a combination of Layer 2 Forwarding (L2F) protocol and PPTP, making use of the best features of both. Since the L2TP standard does not implement encryption , it is usually implemented with an IETF standard known as L2TP/IPsec, in which L2TP packets are encapsulated by IPsec. The client communicates with a Local Access Concentrator (LAC) and the LAC communicates across the Internet with a L2TP Network Server (LNS). The D-Link Firewall acts as the LNS. The LAC is, in effect, tunneling data, such as a PPP session, using IPsec to the LNS across the Internet. In most cases the client will itself act as the LAC. L2TP is certificate based and therefore is simpler to administer with a large number of clients and arguably offers better security than PPTP. Unlike PPTP, it is possible to set up multiple virtual networks across a single tunnel. Being IPsec based, L2TP requires NAT traversal (NAT-T) to be implemented on the LNS side of the tunnel. Example 9.11. Setting up an L2TP server This example shows how to setup a L2TP Network Server. The example presumes that you have created some address objects in the Address Book. You will have to specify the IP address of the L2TP server interface, an outer IP address (that the L2TP server should listen to) and an IP pool that the L2TP server will use to give out IP addresses to the clients from. The interface that the L2TP server will accept connections on is a virtual IPsec tunnel, not illustrated in this example. CLI gw-world:/> add Interface L2TPServer MyL2TPServer ServerIP=ip_l2tp Interface=l2tp_ipsec IP=wan_ip IPPool=L2TP_Pool TunnelProtocol=L2TP AllowedRoutes=all-nets Web Interface 1. Go to Interfaces > L2TP Servers > Add > L2TPServer 2. Enter a suitable name for the L2TP Server, eg. MyL2TPServer 261

Section	Page
User Manual	3
Table of Contents	4
Preface	12
Chapter 1. Product Overview	14
1.1. About D-Link NetDefendOS	14
1.2. NetDefendOS Architecture	16
1.2.1. State-based Architecture	16
1.2.2. NetDefendOS Building Blocks	16
1.2.3. Basic Packet Flow	17
1.3. NetDefendOS State Engine Packet Flow	19
Chapter 2. Management and Maintenance	23
2.1. Managing NetDefendOS	23
2.1.1. Overview	23
2.1.2. Default Administrator Accounts	23
2.1.3. The CLI	24
2.1.4. The WebUI	26
2.1.5. Working with Configurations	29
2.2. Events and Logging	35
2.2.1. Overview	35
2.2.2. Event Messages	35
2.2.3. Event Message Distribution	35
2.2.3.1. Logging to Syslog Hosts	36
2.2.3.2. SNMP Traps	37
2.3. RADIUS Accounting	39
2.3.1. Overview	39
2.3.2. RADIUS Accounting Messages	39
2.3.3. Interim Accounting Messages	41
2.3.4. Activating RADIUS Accounting	41
2.3.5. RADIUS Accounting Security	41
2.3.6. RADIUS Accounting and High Availability	41
2.3.7. Handling Unresponsive Servers	42
2.3.8. Accounting and System Shutdowns	42
2.3.9. Limitations with NAT	42
2.4. Monitoring	43
2.4.1. SNMP Monitoring	43
2.5. Maintenance	45
2.5.1. Auto-Update Mechanism	45
2.5.2. Configuration Backup and Restore	45
2.5.3. Resetting to Factory Defaults	45
Chapter 3. Fundamentals	48
3.1. The Address Book	48
3.1.1. Overview	48
3.1.2. IP Addresses	48
3.1.3. Ethernet Addresses	50
3.1.4. Address Groups	51
3.1.5. Auto-Generated Address Objects	51
3.2. Services	52
3.2.1. Overview	52
3.2.2. TCP and UDP Based Services	53
3.2.3. ICMP Services	55
3.2.4. Custom IP Protocol Services	55
3.3. Interfaces	57
3.3.1. Overview	57
3.3.2. Ethernet	58
3.3.3. VLAN	60
3.3.4. PPPoE	61
3.3.4.1. Overview of PPP	61
3.3.4.2. PPPoE Client Configuration	62
3.3.5. GRE Tunnels	63
3.3.6. Interface Groups	66
3.4. ARP	68
3.4.1. Overview	68
3.4.2. ARP in NetDefendOS	68
3.4.3. ARP Cache	68
3.4.4. Static and Published ARP Entries	69
3.4.5. Advanced ARP Settings	71
3.5. The IP Rule Set	73
3.5.1. Security Policies	73
3.5.2. IP Rule Evaluation	74
3.5.3. IP Rule Actions	75
3.5.4. Editing IP rule set Entries	76
3.6. Schedules	77
3.7. X.509 Certificates	79
3.7.1. Overview	79
3.7.2. X.509 Certificates in NetDefendOS	80
3.8. Setting Date and Time	82
3.8.1. General Date and Time Settings	82
3.8.2. Time Servers	83
3.9. DNS Lookup	87
Chapter 4. Routing	89
4.1. Overview	89
4.2. Static Routing	90
4.2.1. Basic Principles of Routing	90
4.2.2. Static Routing	91
4.2.3. Route Failover	94
4.2.4. Proxy ARP	96
4.3. Policy-based Routing	98
4.3.1. Overview	98
4.3.2. Policy-based Routing Tables	98
4.3.3. Policy-based Routing Rules	98
4.3.4. Policy-based Routing Table Selection	99
4.3.5. The Ordering parameter	99
4.4. Dynamic Routing	103
4.4.1. Dynamic Routing overview	103
4.4.2. OSPF	104
4.4.3. Dynamic Routing Policy	107
4.5. Multicast Routing	110
4.5.1. Overview	110
4.5.2. Multicast Forwarding using the SAT Multiplex Rule	110
4.5.2.1. Multicast Forwarding - No Address Translation	111
4.5.2.2. Multicast Forwarding - Address Translation Scenario	112
4.5.3. IGMP Configuration	114
4.5.3.1. IGMP Rules Configuration - No Address Translation	115
4.5.3.2. IGMP Rules Configuration - Address Translation	116
4.6. Transparent Mode	119
4.6.1. Overview of Transparent Mode	119
4.6.2. Comparison with Routing mode	119
4.6.3. Transparent Mode Implementation	119
4.6.4. Enabling Transparent Mode	120
4.6.5. High Availability with Transparent Mode	120
4.6.6. Transparent Mode Scenarios	120
Chapter 5. DHCP Services	127
5.1. Overview	127
5.2. DHCP Servers	128
5.3. Static DHCP Assignment	130
5.4. DHCP Relaying	131
5.5. IP Pools	132
Chapter 6. Security Mechanisms	135
6.1. Access Rules	135
6.1.1. Introduction	135
6.1.2. IP spoofing	135
6.1.3. Access Rule Settings	136
6.2. Application Layer Gateways	138
6.2.1. Overview	138
6.2.2. HTTP	139
6.2.3. FTP	140
6.2.4. TFTP	145
6.2.5. SMTP	146
6.2.5.1. DNSBL SPAM Filtering	147
6.2.6. POP3	151
6.2.7. SIP	152
6.2.8. H.323	155
6.3. Web Content Filtering	169
6.3.1. Overview	169
6.3.2. Active Content Handling	169
6.3.3. Static Content Filtering	170
6.3.4. Dynamic Web Content Filtering	172
6.3.4.1. Content Filtering Categories	176
6.4. Anti-Virus Scanning	183
6.4.1. Overview	183
6.4.2. Implementation	183
6.4.3. Activating Anti-Virus Scanning	184
6.4.4. The Signature Database	184
6.4.5. Subscribing to the D-Link Anti-Virus Service	184
6.4.6. Anti-Virus Options	184
6.5. Intrusion Detection and Prevention	188
6.5.1. Overview	188
6.5.2. IDP Availability in D-Link Models	188
6.5.3. IDP Rules	190
6.5.4. Insertion/Evasion Attack Prevention	191
6.5.5. IDP Pattern Matching	192
6.5.6. IDP Signature Groups	192
6.5.7. IDP Actions	194
6.5.8. SMTP Log Receiver for IDP Events	194
6.6. Denial-Of-Service (DoS) Attacks	198
6.6.1. Overview	198
6.6.2. DoS Attack Mechanisms	198
6.6.3. Ping of Death and Jolt Attacks	198
6.6.4. Fragmentation overlap attacks: Teardrop, Bonk, Boink and Nestea	199
6.6.5. The Land and LaTierra attacks	199
6.6.6. The WinNuke attack	199
6.6.7. Amplification attacks: Smurf, Papasmurf, Fraggle	200
6.6.8. TCP SYN Flood Attacks	201
6.6.9. The Jolt2 Attack	201
6.6.10. Distributed DoS Attacks	201
6.7. Blacklisting Hosts and Networks	202
Chapter 7. Address Translation	204
7.1. Dynamic Network Address Translation	204
7.2. NAT Pools	207
7.3. Static Address Translation	210
7.3.1. Translation of a Single IP Address (1:1)	210
7.3.2. Translation of Multiple IP Addresses (M:N)	213
7.3.3. All-to-One Mappings (N:1)	215
7.3.4. Port Translation	216
7.3.5. Protocols handled by SAT	216
7.3.6. Multiple SAT rule matches	217
7.3.7. SAT and FwdFast Rules	217
Chapter 8. User Authentication	220
8.1. Overview	220
8.2. Authentication Setup	221
8.2.1. Setup Summary	221
8.2.2. The Local Database	221
8.2.3. External Authentication Servers	221
8.2.4. Authentication Rules	222
8.2.5. Authentication Processing	223
8.2.6. HTTP Authentication	223
Chapter 9. VPN	229
9.1. Overview	229
9.1.1. The Need for VPNs	229
9.1.2. VPN Encryption	229
9.1.3. VPN Planning	229
9.1.4. Key Distribution	230
9.2. VPN Quickstart Guide	231
9.2.1. IPsec LAN to LAN with Pre-shared Keys	231
9.2.2. IPsec Roaming Clients with Pre-shared Keys	232
9.2.3. IPsec Roaming Clients with Certificates	234
9.2.4. L2TP Roaming Clients with Pre-Shared Keys	234
9.2.5. L2TP Roaming Clients with Certificates	236
9.2.6. PPTP Roaming Clients	236
9.2.7. VPN Troubleshooting	237
9.3. IPsec	240
9.3.1. Overview	240
9.3.2. Internet Key Exchange (IKE)	240
9.3.3. IKE Authentication	245
9.3.4. IPsec Protocols (ESP/AH)	247
9.3.5. NAT Traversal	248
9.3.6. Proposal Lists	249
9.3.7. Pre-shared Keys	250
9.3.8. Identification Lists	251
9.4. IPsec Tunnels	253
9.4.1. Overview	253
9.4.2. LAN to LAN Tunnels with Pre-shared Keys	253
9.4.3. Roaming Clients	253
9.4.3.1. PSK based client tunnels	254
9.4.3.2. Self-signed Certificate based client tunnels	255
9.4.3.3. CA Server issued Certificates based client tunnels	256
9.4.3.4. Using Config Mode	257
9.4.4. Fetching CRLs from an alternate LDAP server	259
9.5. PPTP/L2TP	260
9.5.1. PPTP	260
9.5.2. L2TP	261
Chapter 10. Traffic Management	267
10.1. Traffic Shaping	267
10.1.1. Introduction	267
10.1.2. Traffic Shaping in NetDefendOS	268
10.1.3. Simple Bandwidth Limiting	269
10.1.4. Limiting Bandwidth in Both Directions	270
10.1.5. Creating Differentiated Limits with Chains	271
10.1.6. Precedences	272
10.1.7. Guarantees	274
10.1.8. Differentiated Guarantees	274
10.1.9. Groups	275
10.1.10. Recommendations	276
10.1.11. A Summary of Traffic Shaping	277
10.2. Threshold Rules	279
10.2.1. Overview	279
10.2.2. Connection Rate/Total Connection Limiting	279
10.2.3. Grouping	279
10.2.4. Rule Actions	279
10.2.5. Multiple Triggered Actions	280
10.2.6. Exempted Connections	280
10.2.7. Threshold Rules and ZoneDefense	280
10.2.8. Threshold Rule Blacklisting	280
10.3. Server Load Balancing	281
10.3.1. Overview	281
10.3.2. Identifying the Servers	282
10.3.3. The Load Distribution Mode	282
10.3.4. The Distribution Algorithm	282
10.3.5. Server Health Monitoring	284
10.3.6. SLB_SAT Rules	284
Chapter 11. High Availability	289
11.1. Overview	289
11.2. High Availability Mechanisms	291
11.3. High Availability Setup	293
11.3.1. Hardware Setup	293
11.3.2. NetDefendOS Setup	294
11.3.3. Verifying Cluster Functioning	294
11.4. High Availability Issues	296
Chapter 12. ZoneDefense	298
12.1. Overview	298
12.2. ZoneDefense Switches	299
12.3. ZoneDefense Operation	300
12.3.1. SNMP	300
12.3.2. Threshold Rules	300
12.3.3. Manual Blocking and Exclude Lists	300
12.3.4. Limitations	302
Chapter 13. Advanced Settings	304
13.1. IP Level Settings	304
13.2. TCP Level Settings	307
13.3. ICMP Level Settings	311
13.4. ARP Settings	312
13.5. Stateful Inspection Settings	314
13.6. Connection Timeouts	316
13.7. Size Limits by Protocol	318
13.8. Fragmentation Settings	320
13.9. Local Fragment Reassembly Settings	324
13.10. DHCP Settings	325
13.11. DHCPRelay Settings	326
13.12. DHCPServer Settings	327
13.13. IPsec Settings	328
13.14. Logging Settings	330
13.15. Time Synchronization Settings	331
13.16. PPP Settings	333
13.17. Hardware Monitor Settings	334
13.18. Packet Re-assembly Settings	335
13.19. Miscellaneous Settings	336
Appendix A. Subscribing to Security Updates	338
Appendix B. IDP Signature Groups	340
Appendix C. Checked MIME filetypes	344
Appendix D. The OSI Framework	348
Appendix E. D-Link worldwide offices	349

Match case Limit results 1 per page

gw-world:/>

add Interface L2TPServer MyPPTPServer ServerIP=lan_ip Interface=any

IP=wan_ip IPPool=pp2p_Pool TunnelProtocol=PPTP AllowedRoutes=all-nets

Web Interface

Go to

Interfaces > L2TP Servers > Add > L2TPServer

Enter a name for the PPTP Server eg. MyPPTPServer.

Now enter:

•

Inner IP Address:

lan_ip

•

Tunnel Protocol:

PPTP

•

Outer Interface Filter:

any

•

Outer Server IP:

wan_ip

Under the

PPP Parameters

tab, select

pptp_Pool

in the

IP Pool

control

Under the

Add Route

tab, select

all_nets

from

Allowed Networks

Click

Use User Authentication Rules

is enabled as default. To be able to authenticate the users using the PPTP

tunnel you also need to configure authentication rules, which will not be covered in this example.

9.5.2. L2TP

Layer 2 Tunneling protocol (L2TP) is an IETF open standard that overcomes many of the problems

of PPTP. Its design is a combination of Layer 2 Forwarding (L2F) protocol and PPTP, making use

of the best features of both. Since the L2TP standard does not implement encryption , it is usually

implemented with an IETF standard known as L2TP/IPsec, in which L2TP packets are encapsulated

by IPsec. The client communicates with a Local Access Concentrator (LAC) and the LAC

communicates across the Internet with a L2TP Network Server (LNS). The D-Link Firewall acts as

the LNS. The LAC is, in effect, tunneling data, such as a PPP session, using IPsec to the LNS across

the Internet. In most cases the client will itself act as the LAC.

L2TP is certificate based and therefore is simpler to administer with a large number of clients and

arguably offers better security than PPTP. Unlike PPTP, it is possible to set up multiple virtual

networks across a single tunnel. Being IPsec based, L2TP requires NAT traversal (NAT-T) to be

implemented on the LNS side of the tunnel.

Example 9.11. Setting up an L2TP server

This example shows how to setup a L2TP Network Server. The example presumes that you have created some

address objects in the Address Book. You will have to specify the IP address of the L2TP server interface, an

outer IP address (that the L2TP server should listen to) and an IP pool that the L2TP server will use to give out IP

addresses to the clients from. The interface that the L2TP server will accept connections on is a virtual IPsec

tunnel, not illustrated in this example.

CLI

gw-world:/>

add Interface L2TPServer MyL2TPServer ServerIP=ip_l2tp

Interface=l2tp_ipsec IP=wan_ip IPPool=L2TP_Pool TunnelProtocol=L2TP

AllowedRoutes=all-nets

Web Interface

Go to

Interfaces > L2TP Servers > Add > L2TPServer

Enter a suitable name for the L2TP Server, eg.

MyL2TPServer

9.5.2. L2TP

Chapter 9. VPN

261