Denon AVR 1609 Owners Manual - English - Page 19

Connecting the Power Cord, Once Connections are Completed - troubleshoot

Get Denon AVR 1609 - AV Receiver PDF manuals and user guides
UPC - 083795000424
View all Denon AVR 1609 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting Specifications n AM loop antenna assembly Connect to the AM antenna terminals. Remove the vinyl tie and take out the connection line. a. With the antenna on top of any stable surface. Bend in the reverse direction. b. With the antenna attached to a wall. Mount Installation hole Mount on wall, etc. NOTE • Do not connect two FM antennas simultaneously. • Even if an external AM antenna is used, do not disconnect the AM loop antenna. • Make sure the AM loop antenna lead terminals do not touch metal parts of the panel. External Controller Connecting a Room-to-Room Remote Control Unit Connecting the Power Cord Wait until all connections have been completed before connecting the power cord. ENGLISH Power cord To household power outlet (AC 120 V, 60 Hz) Connection to the AC outlets • These outlets supply power to external audio equipment. • The power supplied from these outlets turns on and off together with the set's power switch. • Audio equipment with a total power consumption of 120 W (1 A) can be connected. NOTE • Insert the AC plugs securely. Incomplete connections could cause noise. • Only use the AC outlets to plug in audio equipment. Do not use them as power supplies for hairdryers or anything other than audio equipment. Once Connections are Completed Turning the Power On (vpage 37) "69 065 Infrared retransmitter Input Output Infrared sensor Extension jack for future use. (Connect devices corresponding with room to room function to this jack.) 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
±¶
Getting Started
Setup
Playback
Remote Control
Multi-Zone
Information
Troubleshooting
ENGLISH
Specifications
n
AM loop antenna assembly
Remove the vinyl tie and take
out the connection line.
Connect to the AM
antenna terminals.
Bend in the reverse direction.
a. With the antenna on top of
any stable surface.
Mount
b. With the antenna attached
to a wall.
Installation hole Mount on wall, etc.
NOTE
• Do not connect two FM antennas simultaneously.
• Even if an external AM antenna is used, do not disconnect the AM loop antenna.
• Make sure the AM loop antenna lead terminals do not touch metal parts of the panel.
External Controller
Input
Output
Infrared
retransmitter
Infrared
sensor
Extension jack for future use.
(Connect devices corresponding
with room to room function to
this jack.)
Connecting a Room-to-Room Remote Control Unit
NOTE
• Insert the AC plugs securely. Incomplete connections could cause noise.
• Only use the AC outlets to plug in audio equipment. Do not use them as power supplies for hairdryers or
anything other than audio equipment.
Wait until all connections have been completed before connecting the power cord.
To household
power outlet
(AC 120 V, 60 Hz)
Power cord
Connection to the AC outlets
• These outlets supply power to external audio
equipment.
• The power supplied from these outlets turns on and
off together with the set’s power switch.
• Audio equipment with a total power consumption
of 120 W (1 A) can be connected.
Turning the Power On
(
v
page 37)
Connecting the Power Cord
Once Connections are Completed
Connections