Dewalt DCS372B Instruction Manual - Page 15

Switch Fig. 2, Changing Blades Fig. 1, 4-6

Get Dewalt DCS372B PDF manuals and user guides View all Dewalt DCS372B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Switch (Fig. 2) The saw is controlled by a trigger switch (A) and lock off button (B). The lock off button must be pressed before the trigger switch will turn the saw on. Releasing the trigger turns the saw off. NOTE: This tool has no provision to lock the switch on. The saw should never be locked on by any means. Changing Blades (Fig. 1, 4-6) WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury. TO INSTALL THE BLADE FIG. 4 1. Place inner clamp washer (O) on saw spindle with the large flat surface D facing out toward the blade (Fig. 4, 5). 2. Retract the lower blade P F guard (G) and place blade on saw spindle against the inner clamp washer O (O), making sure that the blade will rotate in the proper direction (the direction of the rotation arrow on the saw blade and the teeth must point in the same direction as the direction of rotation arrow on the saw). Do not assume that the printing on the blade will always be facing you when properly installed. When retracting the lower blade guard to install the blade, check the condition and operation of the lower blade guard to assure that it is working properly. Make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. FIG. 5 SPINDLE O O P BLADE 13 F P F English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
13
English
Switch (Fig. 2)
The saw is controlled by a trigger switch (A) and lock off button (B).
The lock off button must be pressed before the trigger switch will turn
the saw on. Releasing the trigger turns the saw off.
NOTE:
This tool has no provision to lock the switch on. The saw
should never be locked on by any means.
Changing Blades (Fig. 1, 4–6)
WARNING:
To reduce the risk of injury, turn unit off and
disconnect it from power source before installing and removing
accessories, before adjusting or when making repairs.
An
accidental start-up can cause injury.
TO INSTALL THE BLADE
O
FIG. 4
D
P
F
1. Place inner clamp washer
(O) on saw spindle with
the large flat surface
facing out toward the
blade (Fig. 4, 5).
2. Retract the lower blade
guard (G) and place blade
on saw spindle against
the inner clamp washer
(O), making sure that the blade will rotate in the proper direction
(the direction of the rotation arrow on the saw blade and the teeth
must point in the same direction as the direction of rotation arrow
on the saw). Do not assume that the printing on the blade will
always be facing you when properly installed. When retracting the
lower blade guard to install the blade, check the condition and
operation of the lower blade guard to assure that it is working
properly. Make sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
FIG. 5
F
P
O
F
P
BLADE
O
SPINDLE