Electrolux EFLW427UIW Wiring Diagram English - Page 3

Demo Mode/Washer Error Codes 3 Demo Mode: The Demo works in two ways: Interactive Mode and Automatic Loop. The Interactive Mode enables the customer to use the interface without activating the appliance. The machine behavior appears similar to normal operation. With the door closed, pressing start, the appliance turns on and the display counts down by the second from the maximum time displayed with its respective cycle. The appliance turns off when it reaches " ". The Automatic Loop will engage if no one interacts with the user interface for 3 minutes, or the start button hasn't been pressed. The machine will simulate a cycle execution on the display only. Entering Demo Mode: 1 Press power and look for console light up. 2 For Rotary Dial Cycle Select Washer: Within 10 seconds select fast wash and then simultaneously press and hold temp and select (set) buttons for 3 secs. Skip to Step 4. 3 For Push Button Cycle Select Washer: Within 10 seconds select rinse & spin and then simultaneously press and hold temp and select (set) buttons for 3 secs. Continue to Step 4. 4 The message " " will blink 3 times in the center display. 5 If " " message does not appear, turn off machine and repeat previous steps. NOTE Exiting Demo Mode: 1 Press power to turn the unit OFF. 2 Press power to turn the unit ON. The unit display will flash " " 3 times on the numeric display. 3 Within 10 seconds perform steps 4 and 5. 4 Rotate cycle selector ring (on some models) or repeatedly press cycle button to the 6th position. 5 Press and hold temp and select (set) simultaneously for 3 seconds. The appliance will beep once, the numeric display will cycle OFF and ON. The appliance will then beep with the normal power on sequence. You may also perform factory default reset. See below. Factory Default Reset: 1 Press power and look for console light up. 2 Wait at least 10 seconds, then simultaneously press and hold soil and options buttons for 3 secs. To return to factory settings, press the soil and options buttons at the same time and hold until the signal sounds. Once Demo Mode is activated, every time the machine is turned on, Demo Mode is automatically recalled; this occurrence is signaled at the start-up by the text " " flashing 3 times in the center display. Unplugging the unit will not clear Demo Mode. See "Exiting Demo Mode" for more information. Washer Error Codes Recalling Last Error Code: 1 Press power and look for console light up. 2 Wait at least 10 seconds, then simultaneously press and hold temp and select (set) buttons for 3 secs. 3 The display will show the last error in memory. 4 Clear the display and return to normal operation by touching any button or by pressing the power button. Error Code 11 13 21 23 24 31 Error Description Fill time too long Water leak in tub or in pressure sensor Water not pumping out fast enough Drain triac error Drain triac error sensing Electronic pressure switch error Display Notification Yes No Yes No No No Next Step Refer to test (1) Refer to test (2) Refer to test (3) Refer to test (3) Refer to test (3) Refer to test (4) 32 Pressure sensor calibration problem No Refer to test (4) 35 Pressure sensor indicates water overfill Yes Refer to test (5) 38 Air trap clogged No Refer to test (5) 41 Control board thinks the door switch is open Yes Refer to test (6) 42 Door lock device failure No Refer to test (6) 43 Door lock triac failure No Refer to test (6) 44 Door closed sensing failure No Refer to test (6) 45 Line door sensing failure No Refer to test (6) 55 Motor under speed (select models) (not available on 300 series) No Check for heavy or unbalanced load Refer to test (9) 57 High current on inverter (motor control) No Refer to test (8) 58 High current on motor phase No Refer to test (8) 59 No spin signal for 3 seconds No Refer to test (9) 5A High temperature on control due to overload (motor control) No Refer to test (8) 5B Motor control under voltage No Check supply under load and wiring to unit Refer to tests (6 and 9)