Epson 680Pro Product Information Guide - Page 14
Changing the Default Settings, as described in the language selection instructions. - lq esc p 2 driver
UPC - 010343832138
View all Epson 680Pro manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
EPSON LQ-680Pro 8. Turn the ribbon-tightening knob again to remove any slack in the ribbon and to make sure the ribbon moves freely. 9. Close the printer cover. The printer pauses and cannot print when the printer cover is open. Changing the Default Settings While you can often set the default settings through your application software or printer driver, you may need to change a default setting from the printer's control panel using the default setting mode. The table below lists the default settings (in bold) and options you can select in this mode. Settings Page length for tractor Skip over perforation Auto tear-off Auto line feed Print direction Software 0 slash High speed draft I/F mode Auto I/F wait time Parallel I/F bidirectional mode Packet mode Auto CR (IBM 2390 Plus)* A.G.M. (IBM 2390 Plus)* Options Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5, 11, 70/6, 12, 14, 17 On, Off On, Off On, Off Bi-D, Uni-D, Auto ESC/P2, IBM 2390 Plus 0, 0 On, Off Auto, Parallel, Optional 10 seconds, 30 seconds On, Off Auto, Off On, Off On, Off Settings Character table* International character set for Italic table Font Manual feed wait time Buzzer Overlapping forms Options Standard model: Italic, PC 437, PC 850, PC 860, PC 863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15, All other models: Italic, PC 437, PC 850, PC 437 Greek, PC 853, PC 855, PC 852, PC 857, PC 864, PC 866, PC 869, MAZOWIA, Code MJK, ISO 8859-7, ISO Latin 1T, Bulgaria, PC 774, Estonia, ISO 8859-2, PC 866 LAT, PC 866 UKR, PC APTEC, PC 708, PC 720, PC AR864, PC 860, PC863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15, PC 771 Italic U.S.A., Italic France, Italic Germany, Italic U.K., Italic Denmark1, Italic Sweden, Italic Italy, Italic Spain1 OCR-B, Orator, Orator-S, Script C, Roman T, Sans Serif H 0.5 second, 1 second, 1.5 seconds, 2 seconds On, Off On, Off * These settings take effect only when IBM 2390 Plus emulation is selected. Follow the steps below to enter the default setting mode and change the printer's default settings. To print all the instructions, you need 5 sheets of letteror A4-size single-sheet paper or 5 pages of continuous paper. If you use single sheets without a cut-sheet feeder, you need to load a new sheet each time the printer ejects a printed sheet. 1. Make sure paper is loaded and the printer is turned off. Whenever you turn off the printer, wait at least 5 seconds before turning it back on; otherwise you may damage the printer. 2. While holding down the Font button, turn on the printer. The printer enters the default setting mode and prints the language selection instructions. 3. If you need to select a different language, press the Font button until the Font lights indicate the language you want, as described in the language selection instructions. 4. Press the Tear Off/Special Paper button to confirm your language selection and print the current default settings. 5. If you do not need to change any settings, go to step 6. If you want to change any of the default settings, press the Tear Off button to print the instructions (three pages) in the language you selected. Follow these instructions to change the default settings using the buttons on the printer's control panel. 14 - EPSON LQ-680Pro 11/00