Epson BrightLink 710Ui Installation Guide - Ultra-Short Throw Wall Mount ELPMB - Page 26

Drill diameter, 41 in. 10.5 mm, Pilot hole depth, 8 in. 45 mm

Get Epson BrightLink 710Ui PDF manuals and user guides View all Epson BrightLink 710Ui manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

4. Determine the position of the wall plate's mounting holes. Use at least four mounting holes. Steps 5 to 9 below provide instructions for attaching the wall plate to a concrete wall. 5. Drill holes of the following diameters and depths. Drill diameter Pilot hole depth Anchor hole depth 0.41 in. (10.5 mm) 1.8 in. (45 mm) 1.6 in. (40 mm) 6. Remove the template sheet. 7. Use a device such as a dust pump to clean out concrete dust from the hole. 8. Position the wall plate on the wall and insert M10 × 60 mm expansion anchors into the holes. Attach the nut and tap it with a hammer until the core touches the top of the anchor. 9. Tighten the nut with a wrench to secure the wall plate to the wall. 10. Remove the temporary wall plate screw. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
26
4.
Determine the position of the wall plate’s mounting holes.
Use at least four mounting holes.
Steps 5 to 9 below provide instructions for attaching the wall plate to a concrete wall.
5.
Drill holes of the following diameters and depths.
6.
Remove the template sheet.
7.
Use a device such as a dust pump to clean out concrete dust from the hole.
8.
Position the wall plate on the wall and insert M10 × 60 mm expansion anchors into the holes. Attach
the nut and tap it with a hammer until the core touches the top of the anchor.
9.
Tighten the nut with a wrench to secure the wall plate to the wall.
10.
Remove the temporary wall plate screw.
Drill diameter
0.41 in. (10.5 mm)
Pilot hole depth
1.8 in. (45 mm)
Anchor hole depth
1.6 in. (40 mm)