Epson Stylus Pro 10600 Quick Reference Guide

Epson Stylus Pro 10600 Manual

Get Epson Stylus Pro 10600 PDF manuals and user guides View all Epson Stylus Pro 10600 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson Stylus Pro 10600 manual content summary:

  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 1
    sure it's set up as described in Chapter 1 of the Printer Guide. Setting Up the Paper and Spindle 1 Open the roll paper cover and lift out the spindle. 4 Slide the roll carefully and avoid touching the printable side of the paper with bare hands. Fingerprints may affect print quality. 1 Continue
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 2
    avoid damaging the printer, never move the paper set lever while the Operate or Pause light is flashing. If you're using Roll Auto Cut and the leading edge of the paper is uneven, press the Cut/Eject button to recut the edge. 6 Press the Pause button. The print head moves and the
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 3
    then close the lower cover. 6 Press the Pause button. The print head moves and the posterboard feeds into printing position. READY appears on the control panel display. 7 Run your print job. After printing, the posterboard stays in the printer. 8 Hold the posterboard as you pull the paper set lever
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 4
    is flashing or on, you need to replace the corresponding ink cartridge instead. 6 Press the Cleaning button and hold it for at least 3 seconds. The Pause light flashes as the printer cleans its print head. The cleaning cycle takes about a minute and does not use any paper. 2 Press the SelecType
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 5
    straight, you may need to align the print head. Before you begin, print a nozzle check (see page 4) to ensure that the problem is not caused by clogged nozzles. 1 Make sure the printer is turned on and 44-inch wide paper is loaded. (Be sure to use coated ink jet paper, such as the Doubleweight Matte
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 6
    Cyan T549200 • Yellow T549400 • Magenta T549300 * Your printer uses one black ink cartridge (Matte Black or Photo Black). To switch black ink types, you have to follow a special procedure (see your Printer Guide), so be sure to replace the black cartridge with the same type as you are currently
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 7
    package. If you're using Archival or UltraChrome ink, shake the cartridge gently before installing it. 7 Close the ink compartment cover. 5 Hold the cartridge so the arrow mark is on the left side and points to the rear of the printer. Then insert the cartridge into the slot. Don't force it. 7
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 8
    , see your Printer Guide. Message INK LOW INK OUT LOAD ROLL PAPER LOAD SHEET PAPER Light Ink Out light(s) flashing Ink Out light(s) on Paper Out light on Explanation Response Ink cartridge(s) nearly Replace ink cartridge(s) indicated empty (printing continues). by Ink Out light(s). See
  • Epson Stylus Pro 10600 | Quick Reference Guide - Page 9
    : //support.epson.com to download drivers, access product documentation and troubleshooting, and get technical advice through e-mail. Contact the RIP manufacturer. EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON UltraChrome, EPSON Archival, and EPSON Photographic
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
Loading Roll Paper
Loading Roll Paper
Before using the printer, make sure it’s set up as described
in Chapter 1 of the
Printer Guide
.
Setting Up the Paper and Spindle
1
Open the roll paper cover and lift out the spindle.
2
Slide the movable paper stop off the left end of the
spindle.
4
Slide the movable paper stop back onto the spindle
and insert it firmly into the end of the roll.
5
Insert the white
end of the spindle (with the fixed
paper stop) into the right mounting bracket.
1
Continue
paper stop
6
Place the black end of the spindle into the left
mounting bracket.
3
Position the roll so the paper unwinds as
shown, then slide the roll onto the spindle so it
fits securely against the paper stop.
Handle the roll carefully and avoid
touching the printable side of the paper
with bare hands. Fingerprints may affect
print quality.
SP10600 QRG
9/16/02, 05:11 PM
1