Fisher and Paykel DD24DAX9 Installation Manual - Page 11

Secure To The Cabinetry On The Sides, Optionally Secure To The Cabinetry Above, Fit The Supplied

Get Fisher and Paykel DD24DAX9 PDF manuals and user guides View all Fisher and Paykel DD24DAX9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

!1-A SECURE TO THE CABINETRY ON THE SIDES 1 Open the drawer halfway. Using a flat bladed screwdriver, prise the gray rubber plug out of the trim moulding. 2 Replace the gray rubber plug back into the trim moulding and ensure the trim seal is facing forward. 3 !2-A OPTIONALLY SECURE TO THE CABINETRY ABOVE (x2) The top mounting brackets will only bend upwards a maximum of 3/8" (10 mm). Using a small Philips screwdriver, screw through the trim moulding, securing the side mounting bracket to the cabinetry. Do not damage the rubber trimseal. Repeat for all four brackets. !3-A FIT THE SUPPLIED TOEKICK PANEL Where the toekick meets the bottom 3 of the tub is the cut-off point 1 Lay the toekick face down on a chopping board or similiar 5 19 Turn the toekick over and score along the same line 7 Smooth the edge with a file. Be careful of sharp edges. Mounting rail 9 2 6 4 19 8 Slide the toekick onto the mounting rails either side and screw the toekick onto the bottom of tub on either side. Mark this point on the Score along the marked Gently snap off the excess Snap off the two end tabs IMPORTANT! toekick with a pencil cutoff line with a knife Do not overtighten screw. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
10
!1
-
A
SECURE TO THE CABINETRY ON THE SIDES
!2
-
A
OPTIONALLY SECURE TO THE CABINETRY ABOVE
2
1
3
Open the
drawer halfway.
Using a flat
bladed
screwdriver,
prise the gray
rubber plug out
of the trim
moulding.
Replace the gray
rubber plug back into
the trim moulding
and ensure the trim
seal is facing forward.
Repeat for all
four brackets.
Using a small
Philips screwdriver,
screw through the
trim moulding,
securing the side
mounting bracket
to the cabinetry.
Do not damage
the rubber
trimseal.
(x2)
The top mounting
brackets will only
bend upwards a
maximum of 3/8”
(10 mm).
!3
-
A
FIT THE SUPPLIED TOEKICK PANEL
19
1
3
5
7
8
9
2
6
4
19
IMPORTANT!
Do not overtighten screw.
Where the toekick
meets the bottom
of the tub is the
cut-off point
Mark this point on the
toekick with a pencil
Lay the toekick face down on
a chopping board or similiar
Smooth the edge with a file.
Be careful of sharp edges.
Snap off the two end tabs
Slide the toekick onto
the mounting rails
either side and screw
the toekick onto the
bottom of tub on
either side.
Mounting rail
Score along the marked
cutoff line with a knife
Turn the toekick over and
score along the same line
Gently snap off the excess