Fisher and Paykel DD24DCHTX9 User Guide - Page 36

Removing the drain filter and filter plate, to clean, Replacing the filter plate and drain filter

Get Fisher and Paykel DD24DCHTX9 PDF manuals and user guides View all Fisher and Paykel DD24DCHTX9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

USER MAINTENANCE INSTRUCTIONS Removing the drain filter and filter plate to clean 3 Twist the circular drain filter anti/counterclockwise and lift to remove. It is normal to find some water under it. 4 Remove the drain filter mesh by pinching one side only and pulling it off, as shown. Note: Do not attempt to remove the drain filter mesh by pinching two opposing sides together as this may damage the drain filter mesh. 5 Wash both parts of the drain filter in hot soapy water and rinse thoroughly under running water. 6 Carefully lift the filter plate out. Remove any foreign material on either side, wash in hot soapy water and rinse thoroughly in clean water, then wipe with a damp cloth. Replacing the filter plate and drain filter 7 Carefully replace the filter plate. Ensure it is fully pushed into position. 8 Refit the circular drain filter: a Push the drain filter mesh back onto the holder. It should click into place. b Rotate the drain filter mesh until the arrow on the mesh filter lines up with the arrow on the holder. c Refit the drain filter into the drain hole by lining up the arrow on the top of the drain filter with the arrow on the filter plate. d Rotate the drain filter clock wise until the arrow on the drain filter lines up with the arrow on the base of the drawer. 9 Either replace the whole base rack (if removed) and/or replace the fixed tine plate rack. Ensure the rack is replaced correctly (the rear of the rack sits underneath the anchoring loop and the right side rail of the fixed tine plate rack sits inside the stop as shown on previous page). !0 Fold down the trap door so it is resting on the fixed tine plate rack and replace the cutlery basket. Holder Drain filter Drain filter mesh Pinch one side and pull off mesh. After cleaning the mesh, push back on. Rotate the mesh anticlockwise until the arrows line up as shown. Filter plate Line up the arrows on the filter Rotate the drain filter clockwise plate and insert the drain filter until these arrows line up as shown 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
32
USER MAINTENANCE INSTRUCTIONS
Removing the drain filter and filter plate
to clean
3
Twist the circular drain filter anti/counter-
clockwise and lift to remove. It is normal to
find some water under it.
4
Remove the drain filter mesh by pinching
one side only and pulling it off, as shown.
Note: Do not attempt to remove the drain
filter mesh by pinching two opposing sides
together as this may damage the drain
filter mesh.
5
Wash both parts of the drain filter in hot
soapy water and rinse thoroughly under
running water.
6
Carefully lift the filter plate out. Remove
any foreign material on either side, wash
in hot soapy water and rinse thoroughly in
clean water, then wipe with a damp cloth.
Replacing the filter plate and drain filter
7
Carefully replace the filter plate. Ensure it
is fully pushed into position.
8
Refit the circular drain filter:
a Push the drain filter mesh back onto the
holder. It should click into place.
b Rotate the drain filter mesh until the
arrow on the mesh filter lines up with the
arrow on the holder.
c Refit the drain filter into the drain hole by
lining up the arrow on the top of the drain
filter with the arrow on the filter plate.
d Rotate the drain filter clock wise until the
arrow on the drain filter lines up with the
arrow on the base of the drawer.
9
Either replace the whole base rack (if
removed) and/or replace the fixed tine
plate rack. Ensure the rack is replaced
correctly (the rear of the rack sits
underneath the anchoring loop and the
right side rail of the fixed tine plate rack
sits inside the stop as shown on previous
page).
!0
Fold down the trap door
so it is resting on the
fixed tine plate rack and
replace the cutlery basket.
Drain filter
Drain filter mesh
Holder
After cleaning the
mesh, push back on.
Rotate the mesh anti-
clockwise until the
arrows line up as shown.
Pinch one side and
pull off mesh.
Filter plate
Line up the arrows on the filter
plate and insert the drain filter
Rotate the drain filter clockwise
until these arrows line up as shown