Gateway LX6200 8513217 - Gateway Hardware Reference Guide - Page 54

Closing the case, Adding or replacing memory

Page 54 highlights

CHAPTER 5: Upgrading Your Computer Closing the case Replacing the front bezel To replace the front bezel: 1 Slide the hinge tabs on the right side of the bezel into the slots on the front of the computer, then press the left side of the bezel against the computer until its tabs snap into place. 2 Replace the side panels that you removed previously by following the instructions in "Replacing the side panels" on page 48. Replacing the side panels To replace the side panels: 1 Make sure that all internal cables are arranged inside the computer so they will not be pinched when you close the computer. 2 Slide the side panels toward the front of the computer until the backs of the side panels are flush with the back of the computer. 3 Secure each side panel with the two Phillips screws you removed previously. 4 Reconnect the cables and power cord. Adding or replacing memory When you upgrade the computer memory, make sure that you install the correct type of memory module for your computer. Your computer uses DIMM memory. To install or replace DIMM memory: 1 Remove the side panel by following the instructions in "Removing the left side panel" on page 45. 2 For more stability, place your computer on its side. To avoid scratching the case, place it on a towel or other non-abrasive surface. 3 Find the memory module banks on your system board. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136

CHAPTER 5: Upgrading Your Computer
48
Closing the case
Replacing the front bezel
To replace the front bezel:
1
Slide the hinge tabs on the right side of the bezel into
the slots on the front of the computer, then press the left
side of the bezel against the computer until its tabs snap
into place.
2
Replace the side panels that you removed previously by
following the instructions in
“Replacing the side panels”
on page 48
.
Replacing the side panels
To replace the side panels:
1
Make sure that all internal cables are arranged inside the
computer so they will not be pinched when you close the
computer.
2
Slide the side panels toward the front of the computer
until the backs of the side panels are flush with the back
of the computer.
3
Secure each side panel with the two Phillips screws you
removed previously.
4
Reconnect the cables and power cord.
Adding or replacing memory
When you upgrade the computer memory, make sure that you
install the correct type of memory module for your computer.
Your computer uses DIMM memory.
To install or replace DIMM memory:
1
Remove the side panel by following the instructions in
“Removing the left side panel” on page 45
.
2
For more stability, place your computer on its side. To
avoid scratching the case, place it on a towel or other
non-abrasive surface.
3
Find the memory module banks on your system board.