GE CT9070SHSS Installation Instructions

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

Save these instructions

for local inspector’s use.

•

Observe all governing

codes and ordinances.

•

Note to Installer –

Be sure to leave these

instructions with Consumer.

•

Note to Consumer –

Keep these instructions

for future reference.

•

Skill level –

Installation of this appliance

requires a qualified installer or electrician.

•

Proper installation is the responsibility

of the installer.

•

Product failure due to improper installation

is not covered under Warranty.

•

Product is for indoor use only.

Installation Instructions

30” French Door Built-in Wall Ovens

FOR YOUR SAFETY:

WARNING

:

Before beginning the installation, switch power off at the service panel and

lock the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.

Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,

stand or hang on the oven door.

Make sure the wall coverings, counters and cabinets around the oven can withstand the heat

(up to 200°F [93.3°C]) generated by the oven.

Questions?

Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

MATERIALS YOU MAY NEED

Junction Box

Wire Nuts

Strain Relief Clamp for 1/2” Conduit

TOOLS YOU MAY NEED

1/8” Drill Bit and Electric or Hand Drill

Phillips Screwdriver

Wire Strippers

9/16” Socket Wrench

1/8” Hex Key

1

REMOVE PACKAGING MATERIALS

Failure to remove packaging materials could result in damage to the appliance. Remove all packing

parts from oven, racks and heating elements. Remove protective film and labels on the outer door

and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping

screws securing the oven to the base pad. Open oven door and remove literature pack and oven

racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation

process. The trim is wrapped separately and taped to the top of the unit.

2

PREPARE THE OPENING

NOTE:

If the cabinet does not have a solid bottom, two

braces or runners must be installed to support the weight

of the oven. For French Door ovens, the runners and

braces must support 220 lbs (98.8 kg).

NOTE:

If marks, blemishes or the cutout opening are

visible above the installed oven, it may be necessary to

add wood shims under the runners and front trim until

the marks or opening are covered.

NOTE:

If the cabinet does not have a front frame and

the sides are less than ¾” (1.9 cm) thick, shim both sides

equally to establish the cutout width.

ATTENTION INSTALLER:

All electric wall ovens must be hard-wired (direct-wired) into an

approved junction box. A plug and receptacle is NOT permitted on these products.

C

L

2" x 4" (5 cm x 10 cm)

or Equivalent Runners Level

with Bottom of Cutout

and Flush with Sides of Cutout

DESIGN INFORMATION

FRENCH DOOR SINGLE OVEN INSTALLATIONS

The French Door single oven may be installed in a cabinet alone or above a warming drawer and/or below a

Microwave/Advantium. However, the French Door single oven is not allowed under a countertop or cooktop,

and it is not allowed to be installed flush to the front surface of the cabinet.

IMPORTANT:

Always refer to individual installation instructions packed with each product for specific

requirements.

GE CT9070SHSS Installation Instructions

GE CT9070SHSS Manual

GE CT9070SHSS manual content summary: