GE GFWS2605FMC Use and Care Manual - Page 24

Floor Type Selection, ADAPTIVE VIBRATION CONTROL

Get GE GFWS2605FMC PDF manuals and user guides View all GE GFWS2605FMC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Installation Instructions ADAPTIVE VIBRATION CONTROL Your GE washer is equipped with Adaptive Vibration Control Technology. Using information about the floor, this system can reduce vibration and improve spin performance in some installations by adapting the spin cycle. The DEFAULT configuration is specially designed to provide optimal performance across the widest range of floor types. Follow the procedure below to enable more specific adaptive settings. Your washer can be returned quickly and easily to the DEFAULT configuration at any time using the same procedure. Floor Type Selection 1. Place control in the idle state. (Make sure no cycles or options are selected but that the washers Power is on.) 2. Press and hold the Power and Spin buttons at the same time for 3 seconds. 3. Only the Power, Start and display lights will be lit in this mode. 4. Pressing the Power button in this mode will return the control to the idle state and the defaults will be restored. 5. Rotate the selector knob to select the Floor Type, per the following table. Display F0 F1 F2 F3 F4 F5 Floor Type Default Concrete Floor Second Floor, all surface types First Floor, Tile Surface First Floor, Linoleum surface First Floor, wood surface 6. Press the Start button to make selection. o For GE RightHeight Design™ frontload washers with a Built-In Riser™ models (GFWR4800 and GFWR4805) - Exit the Floor Type selection mode and return to the idle state after the Start button is pressed. The programming of your washers Adaptive Vibration Control is now complete. o For all other models (GFWS2500, GFWS2505, GFWS2600, GFWS2605, GHWS3600, GHWS3605, GFWS3700 and GFWS3705) - proceed to the pedestal selection (steps 7-9). 7. Rotate the selector knob to select the Pedestal Type, per the following table. Display P0 P1 Pedestal Type No Pedestal (Default setting) Pedestal 8. Press the Start button to make selection. 9. Exit the Pedestal Type selection mode and return to the idle state after the Start button is pressed. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
24
Installation Instructions
Floor Type Selection
Your GE washer is equipped with Adaptive Vibration Control
Technology. Using information about the floor, this system
can reduce vibration and improve spin performance in
some installations by adapting the spin cycle. The DEFAULT
configuration is specially designed to provide optimal
performance across the widest range of floor types. Follow
the procedure below to enable more specific adaptive
settings. Your washer can be returned quickly and easily
to the DEFAULT configuration at any time using the same
procedure.
ADAPTIVE VIBRATION CONTROL
1. Place control in the idle state. (Make sure no cycles or
options are selected but that the washers
Power
is on.)
2. Press and hold the
Power
and
Spin
buttons at the same
time for 3 seconds.
3. Only the
Power
,
Start
and display lights will be lit in this
mode.
4. Pressing the
Power
button in this mode will return the
control to the idle state and the defaults will be restored.
5. Rotate the selector knob to select the
Floor Type
, per
the following table.
Display
Floor Type
F0
Default
F1
Concrete Floor
F2
Second Floor, all surface types
F3
First Floor, Tile Surface
F4
First Floor, Linoleum surface
F5
First Floor, wood surface
6. Press the
Start
button to make selection.
o For GE RightHeight Design
™
frontload washers with a
Built-In Riser
™
models (GFWR4800 and GFWR4805) – Exit
the
Floor Type
selection mode and return to the idle state
after the
Start
button is pressed. The programming of
your washers Adaptive Vibration Control is now complete.
o
For all other models (
GFWS2500, GFWS2505, GFWS2600
,
GFWS2605
,
GHWS3600
,
GHWS3605
,
GFWS3700
and
GFWS3705
) – proceed to the pedestal selection (steps
7-9).
7. Rotate the selector knob to select the
Pedestal Type
, per
the following table.
8. Press the
Start
button to make selection.
9. Exit the
Pedestal Type
selection mode and return to the
idle state after the
Start
button is pressed.
Display
Pedestal Type
P0
No Pedestal (Default setting)
P1
Pedestal