GE WPDH8800JMV Owners Manual - Page 16

Installation Instructions, LOCATION OF YOUR WASHER, ROUGH-IN DIMENSIONS

Get GE WPDH8800JMV - Profile - 27inch Frontload Washer PDF manuals and user guides
UPC - 084691169772
View all GE WPDH8800JMV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Installation Instructions LOCATION OF YOUR WASHER Do Not Install the Washer: 1. In an area exposed to dripping water or outside weather conditions. The ambient temperature should never be below 60°F (15.6°C) for proper washer operation. 2. In an area where it will come in contact with curtains or drapes. 3. On carpet. The floor MUST be a hard surface with a maximum slope of 1/2″ per foot (1.27 cm per 30 cm). To make sure the washer does not vibrate or move, you may have to reinforce the floor. NOTE: If floor is in poor condition, use 3/4″ impregnated plywood sheet solidly attached to existing floor covering. IMPORTANT: Minimum Installation Clearances • When installed in alcove: Sides, Rear, Top = 0″ (0 cm) • When installed in closet: Sides, Rear, Top = 0″ (0 cm), Front = 1″ (2.54 cm) • Closet door ventilation openings required: 2 louvers each 60 square in. (387 cm2), located 3″ (7.6 cm) from top and bottom of door ROUGH-IN DIMENSIONS FRONT 27.0" (68.6 cm) SIDE 32.1" (81.5 cm) 39.2"* (99.5 cm) 39.2"* (99.5 cm) *NOTE: With Washer Legs: 40.5" (102.5 cm) (0.75" adjustability) With Pedestal: 53.75" (136.6 cm) (0.75" adjustability) Stacked: 82.75" (209.8 cm) 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
16
Installation Instructions
LOCATION OF YOUR WASHER
Do Not Install the Washer:
1.
In an area exposed to dripping water or outside
weather conditions. The ambient temperature
should never be below 60°F (15.6°C) for proper
washer operation.
2.
In an area where it will come in contact with curtains
or drapes.
3.
On carpet. The floor
MUST
be a hard surface with
a maximum slope of 1/2
″
per foot (1.27 cm per
30 cm). To make sure the washer does not vibrate
or move, you may have to reinforce the floor.
NOTE:
If floor is in poor condition, use 3/4
″
impregnated
plywood sheet solidly attached to existing floor covering.
IMPORTANT:
Minimum Installation Clearances
•
When installed in alcove: Sides, Rear,
Top = 0
″
(0 cm)
•
When installed in closet: Sides, Rear,
Top = 0
″
(0 cm), Front = 1
″
(2.54 cm)
•
Closet door ventilation openings required:
2 louvers each 60 square in. (387 cm
2
), located 3
″
(7.6 cm) from top and bottom of door
ROUGH-IN DIMENSIONS
SIDE
FRONT
27.0”
(68.6 cm)
39.2”*
(99.5 cm)
32.1”
(81.5 cm)
39.2”*
(99.5 cm)
*NOTE:
With Washer Legs: 40.5” (102.5 cm)
(0.75” adjustability)
With Pedestal: 53.75” (136.6 cm)
(0.75” adjustability)
Stacked: 82.75” (209.8 cm)