Gigabyte GA-H110TN-M User Manual - Page 14

SATA_PWR SATA Power Connector, BAT Battery, BAT_CON Battery Cable Header

Get Gigabyte GA-H110TN-M PDF manuals and user guides View all Gigabyte GA-H110TN-M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

5) SATA_PWR (SATA Power Connector) This connector provides power to installed SATA devices. Pin No. Definition 1 1 VCC 2 GND 3 GND 4 +12V 6) BAT (Battery) The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost. You may clear the CMOS values by removing the battery cable: 1. Turn off your computer and unplug the power cord. 2. Unplug the battery cable from the battery cable header and wait for one minute. 3. Plug in the battery cable. 4. Plug in the power cord and restart your computer. •• Always turn off your computer and unplug the power cord before replacing the battery. •• Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model. •• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model. •• When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery (the positive side should face up). •• Used batteries must be handled in accordance with local environmental regulations. 7) BAT_CON (Battery Cable Header) 2 1 Pin No. Definition 1 RTC Power 2 GND - 14 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
- 14 -
5)
SATA_PWR (SATA Power Connector)
This connector provides power to installed SATA devices.
Pin No.
Definition
1
VCC
2
GND
3
GND
4
+12V
6)
BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery cable:
1. Turn off your computer and unplug the power cord.
2. Unplug the battery cable from the battery cable header and wait for one minute.
3. Plug in the battery cable.
4. Plug in the power cord and restart your computer.
•
Always turn off your computer and unplug the power cord before replacing the battery.
•
Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with
an incorrect model.
•
Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
•
When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
•
Used batteries must be handled in accordance with local environmental regulations.
7)
BAT_CON (Battery Cable Header)
1
Pin No.
Definition
1
RTC Power
2
GND
2
1