Hannspree ST289MUB User Manual - Page 38

Searching Codes, Setting Volume Lock

Get Hannspree ST289MUB PDF manuals and user guides View all Hannspree ST289MUB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

English 6. During the setting process, only digit keys '0' through '9' are valid inputs, while other buttons are deemed invalid and do not affect the code setting. For example, inputting "02" then pressing RETURN does affect the "02" already input. 6.1.3 Searching Codes If the desired electronic equipment code for setting can not be found on the list in the appendix, try to use the code-searching function with operating procedures as follows: 1. Press the corresponding electronic equipment button. The indicator light will come on for 2 seconds then it goes off; after 3 seconds, the indicator light will come on again, showing that the setting mode has been entered. 2. Hold the electronic equipment button while pressing POWER, then input mode codes 9-9-9 in sequence. If the indicator light does not come on again after going off, the code setting is valid; otherwise the indicator light comes on again after going off for 2 seconds, prompting user to re-enter mode codes. 3. If setting is successful, the electronic equipment code-searching state is entered upon releasing the electronic equipment button. The POWER signal of all manufacturers' codes under the current electronic equipment mode is then transmitted automatically every 5 seconds. 4. During search, the indicator light will flash when the POWER signal of each electronic equipment is transmitted. When one cycle of code-searching is complete, the indicator light will come on for 2 seconds before going off, exiting search mode automatically. 5. Pressing CH+/CH- during search transmits the next/previous electronic equipment POWER signal without waiting for 5 seconds, and resets the timer to trigger another 5 seconds interval. 6. Pressing POWER during search exits search mode without saving the new electronic equipment code; pressing OK during search saves the most recently searched electronic equipment code and then exits search mode. 7. Buttons other than POWER, OK, and CH+/CH- are not functional during search. 6.1.4 Setting Volume Lock Operating procedures are as follows: 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
38
English
6. During the setting process, only digit keys ‘0’ through ‘9’ are valid inputs, while
other buttons are deemed invalid and do not affect the code setting. For example,
inputting “02” then pressing RETURN does affect the “02” already input.
6.1.3
Searching Codes
If the desired electronic equipment code for setting can not be found on the list in the
appendix, try to use the code-searching function with operating procedures as
follows:
1. Press the corresponding electronic equipment button. The indicator light will come
on for 2 seconds then it goes off; after 3 seconds, the indicator light will come on
again, showing that the setting mode has been entered.
2. Hold the electronic equipment button while pressing POWER, then input mode
codes 9-9-9 in sequence. If the indicator light does not come on again after going off,
the code setting is valid; otherwise the indicator light comes on again after going off
for 2 seconds, prompting user to re-enter mode codes.
3. If setting is successful, the electronic equipment code-searching state is entered
upon releasing the electronic equipment button. The POWER signal of all
manufacturers’ codes under the current electronic equipment mode is then
transmitted automatically every 5 seconds.
4. During search, the indicator light will flash when the POWER signal of each
electronic equipment is transmitted. When one cycle of code-searching is complete,
the indicator light will come on for 2 seconds before going off, exiting search mode
automatically.
5. Pressing CH+/CH- during search transmits the next/previous electronic equipment
POWER signal without waiting for 5 seconds, and resets the timer to trigger another
5 seconds interval.
6. Pressing POWER during search exits search mode without saving the new
electronic equipment code; pressing OK during search saves the most recently
searched electronic equipment code and then exits search mode.
7. Buttons other than POWER, OK, and CH+/CH- are not functional during search.
6.1.4
Setting Volume Lock
Operating procedures are as follows: