Harman Kardon AVR 146 Owners Manual - Page 24
Step Six - Plug in AC Power, Step Seven - Insert Batteries in Remote, Step Eight - Program Sources - help
View all Harman Kardon AVR 146 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 24 highlights
INSTALLATION Next, note which types of video connections you used for your source devices. Make sure you didn't use a better type of video connection for a source than your video display can handle. If so, you will need to disconnect the source and use a video connection that's compatible with your display. If you used an HDMI video connection for any of your sources, then connect the HDMI Output on the AVR to an HDMI input on your video display. See Figure 29. As mentioned previously, you will need to make a separate digital audio connection from each source device to the AVR 146, and you will also need to consult the owner's guide for your television to learn the proper procedure for disabling or muting the audio. Step Seven - Insert Batteries in Remote The AVR 146 remote control uses three AAA batteries, which are included. To remove the battery cover located on the back of the remote, firmly press the ridged depression and slide the cover towards the top of the remote. Insert the batteries as shown in Figure 32, making sure to observe the correct polarity. Figure 29 - HDMI Output If you used component video for any sources, connect the Component Video Monitor outputs on the receiver to one set of component video inputs on your display. See Figure 30. Make a note of how these inputs are labeled on the display. Figure 30 - Component Video Monitor Outputs If you used S-video for any sources, or if all of your sources used HDMI or component video, connect the S-video Monitor output on the receiver to an S-video input on your display. See Figure 31. Make a note of how the input is labeled. If you used composite video for any sources, connect the composite video Monitor output on the receiver to a composite video input on the display. See Figure 31. Again, make a note of how this input is labeled on the display. Figure 31 - S-Video and Composite Video Monitor Outputs Consult the manual for your TV to make sure you understand how to select each video input. As you play different source devices that use different types of video connections, select the correct video input on your video display. Step Six - Plug in AC Power Having made all of your wiring connections, it is now time to plug each component's AC power cord into a working outlet. Before plugging the AVR 146's AC Power Cord into an electrical outlet, make sure that the Master Power Switch on the front panel is popped out so that the word OFF appears on its top. Gently press the button to turn the switch off. This will prevent the possibility of damaging the AVR in case of a transient power surge. Figure 32 - Remote Battery Compartment When using the remote, remember to point the lens toward the front panel of the AVR 146. Make sure no objects, such as furniture, are blocking the remote's path to the receiver. Bright lights, fluorescent lights and plasma video displays may interfere with the remote's functioning. The remote has a range of about 20 feet, depending on the lighting conditions. It may be used at an angle of up to 30 degrees to either side of the AVR. If the remote seems to operate intermittently, or if pressing a button on the remote does not cause the AVR Selector or one of the Input Selectors to light up, then make sure the batteries have been inserted correctly, or replace all three batteries with fresh ones. Step Eight - Program Sources Into the Remote The AVR 146 remote not only is capable of controlling the receiver, but it may also be programmed to control many brands and models of VCRs, DVD players, CD players, cable boxes, satellite receivers, cassette decks and TVs, as well as an iPod docked in The Bridge. It may help to think of the remote as a book with pages. Each page represents the button functions for a different device. In order to access the functions for a particular device, you first need to turn to that page, that is, switch the remote to that device mode. This is done by pressing the AVR Button to access the codes that control the receiver, or the Input Selector buttons to access the codes for the devices programmed into the remote. You may have noticed that three of the Input Selectors look different from the others (see Figure 33). For the DVD/CD, TAPE/The Bridge and HDMI 1/HDMI 2 Selectors, there is a primary source, whose name is printed on the button, and a secondary source, whose name is printed in green above the button. To access the code set for the primary source (which also selects that source input on the AVR and turns on the AVR), press the Input Selector once. The Input Selector will light in red to indicate that the primary source is active. 24