Harman Kardon AVR 520 Owners Manual - Page 35

Advanced Features

Get Harman Kardon AVR 520 PDF manuals and user guides View all Harman Kardon AVR 520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Advanced Features To change the length of time that the semi-OSD displays remain on the screen, go to the ADVANCED menu as outlined earlier, and press the ⁄/¤ Buttons n as needed, until the on-screen › cursor is next to the SEMI OSD TIME OUT line. Next, press the ‹/› Buttons o 37 until the desired time in seconds is displayed. Note that unlike most of the other options in this menu, this is a permanent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off. If you wish to make other adjustments, press the ⁄/¤ Buttons n until the on-screen › cursor is next to the desired setting or the RETURN TO MASTER MENU line and press the Set Button p. If you have no other adjustments to make, press the OSD Button v to exit the menu system. Full-OSD Time-Out Adjustment The FULL OSD menu system is used to simplify the setup and adjustment of the AVR 520, using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of inactivity before they disappear from the screen (Time-Out). Time-Out is a safety measure to prevent image retention of the menu text in your monitor or projector, which might happen if it were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the Time Out display. To change the Full-OSD Time-Out, you will need to make an adjustment in the ADVANCED menu (Figure 9). To start the adjustment, press the OSD Button v to bring the MASTER menu to the screen. Press the ¤ Button n six times, until the on-screen ¤ cursor is next to the ADVANCED line. Press the Set Button p to enter the ADVANCED menu (Figure 9). At the ADVANCED menu (Figure 9) make certain that the on-screen › cursor is next to the FULL OSD TIME OUT line by pressing the ⁄/¤ Buttons n as needed. Next, press the ‹/› Buttons o/ 37 until the desired time is displayed in seconds. Note that unlike most of the other options in this menu, this is a permanent setting change, and the Time-Out entry will remain in effect until it is changed, even if the unit is turned off. If you wish to make other adjustments, press the ⁄/¤ Buttons n until the on-screen › cursor is next to the desired setting or the RETURN TO MASTER MENU line and press the Set Button p. If you have no other adjustments to make, press the OSD Button v to exit the menu system. 35 ADVANCED FEATURES

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
35
ADVANCED FEATURES
Advanced Features
To change the length of time that the semi-OSD
displays remain on the screen, go to the
ADVANCED
menu as outlined earlier, and
press the
⁄
/
¤
Buttons
n
as needed, until
the on-screen
›
cursor is next to the
SEMI
OSDTIMEOUT
line. Next, press the
‹
/
›
Buttons
o
until the desired time in sec-
onds is displayed. Note that unlike most of the
other options in this menu, this is a permanent
setting change, and the time-out entry will
remain in effect until it is changed, even when
the unit is turned off.
If you wish to make other adjustments, press
the
⁄
/
¤
Buttons
n
until the on-screen
›
cursor is next to the desired setting or the
RETURNTOMASTERMENU
line and
press the
Set Button
p
. If you have no
other adjustments to make, press the
OSD
Button
v
to exit the menu system.
Full-OSD Time-Out Adjustment
The
FULLOSD
menu system is used to sim-
plify the setup and adjustment of the AVR 520,
using a series of on-screen menus. The factory
default setting for these menus leaves them on
the screen for 20 seconds after a period of
inactivity before they disappear from the screen
(Time-Out). Time-Out is a safety measure to
prevent image retention of the menu text in
your monitor or projector, which might happen
if it were left on indefinitely. However, some
viewers may prefer a slightly longer or shorter
period before the Time Out display.
To change the Full-OSD Time-Out, you will need
to make an adjustment in the
ADVANCED
menu (Figure 9). To start the adjustment, press
the
OSD Button
v
to bring the
MASTER
menu to the screen. Press the
¤
Button
n
six times, until the on-screen
¤
cursor is next
to the
ADVANCED
line. Press the
Set
Button
p
to enter the
ADVANCED
menu
(Figure 9).
At the
ADVANCED
menu (Figure 9) make
certain that the on-screen
›
cursor is next to
the
FULLOSDTIMEOUT
line by press-
ing the
⁄
/
¤
Buttons
n
as needed. Next,
press the
‹
/
›
Buttons
o
/
until the
desired time is displayed in seconds. Note that
unlike most of the other options in this menu,
this is a permanent setting change, and the
Time-Out entry will remain in effect until it is
changed, even if the unit is turned off.
If you wish to make other adjustments, press
the
⁄
/
¤
Buttons
n
until the on-screen
›
cursor is next to the desired setting or the
RETURNTOMASTERMENU
line and
press the
Set Button
p
. If you have no
other adjustments to make, press the
OSD
Button
v
to exit the menu system.
37
37