Harman Kardon AVR 520 Owners Manual - Page 38

the code being sent so that it is facing the

IR Transmitter Window

b

on the

AVR 520 remote “head-to-head.”The

remotes should be between one and three

inches apart.

2. Select the button on the remote that you

wish to use as the device selector for the

codes about to be entered. This may be any

of the

Input Selectors

e

.

3. Press the

Input Selector

e

button

chosen and the

Learn Button

h

at the

same time. Hold these buttons until the

Program/SPL Indicator

c

flashes amber

and the light under the device selector but-

ton turns red. Release the buttons.

4. Press the button on the AVR 520 remote

that you wish to program. Note that the


c

will stop

flashing.

5. Within five seconds, press and hold the but-

ton on the original remote that you wish to

“teach” into the AVR 520 remote. When the


c

turns green

three times, release the button. Note that

the Program Indicator will then begin to

flash amber again.

NOTE

: If the


c

turns red during Step 5 or 6, the program-

ming was not successful. Repeat the steps to

see if the code will “take.”

6. Repeat Steps 4 though 6 for each button on

the source remote that you wish to transfer

to the AVR 520 remote.

7. Once all codes have been transferred from

the original source remote to the AVR 520

remote, press the

Learn Button

h

.

8. Repeat Steps 1 through 7 for any additional

remotes you wish to “teach” into the

AVR 520 Remote.

Erasing Learned Codes

The AVR 520’s remote allows you to remove or

erase, the code learned into a single button for a

single device, to remove or erase the code set for

all the codes that have been programmed into

specific device buttons, or to erase all commands

that have been learned to all devices.

To erase a single learned code from within a sin-

gle device’s settings, follow these steps:

1. Press and hold both the

Input Selector

efg

within which the individual but-

ton to be erased has been programmed and

the

Learn Button

h

.

2. When the red LED under the

Input Selector

turns red and the


c

flashes amber, release the buttons.

3. Press and release the

Input Selector

efg

again for the device within

which the individual button to be erased has

been programmed.

4. Press the

7 Button

r

four times.

5. Press and release the individual button for

which the code is to be erased. The


c

will blink

green two times and then return to amber.

6. To erase other buttons within the same

device, press them as noted in Step 5.

7. When all buttons to be erased have been

pressed, press the

Learn Button

h

to

complete the process.

To erase all codes within a single device, follow

these steps:

1. Press and hold both the

Input Selector

efg

for which you wish to erase the

codes and the

Learn Button

h

.


Input Selector

turns red and the


c



Input Selector

efg

again for the device whose

codes you wish to erase.

4. Press the 8 button

r

four times.

5. The


c

will turn

off and the red light under the

Input

Selector

will flash on and off once to indi-

cate that the codes have been erased.

To erase all codes that have been programmed

to all devices in the remote, follow these steps:

1. Press any

Input Selector

efg

for

which you wish to erase the codes and also

the

Learn Button

h

.


Input Selector

turns red and the


c



Input Selector

efg

again for the device whose

codes you wish to erase.

4. Press the

9 Button

r

four times.

5. The


c

will turn

off and the red light under the

Input

Selector

will flash on and off once to

indicate that the codes have been erased.

Macro Programming

Macros enable you to easily repeat frequently

used combinations of commands with the press

of a single button on the AVR 520’s remote

control. Once programmed, a macro will send

out up to 19 different remote codes in a prede-

termined sequential order enabling you to auto-

mate the process of turning on your system,

changing devices, or other common tasks. The

AVR 520’s remote can store up to five separate

macro command sequences: one that is

associated with the

Power On Button

a

and four more that are accessed by pressing the

Macro Buttons

.

1. Press the

Mute Button

and the

Macro Button

to be programmed or

the

Power On Button

a

at the same

time. Note that an

Input Selector

will

light red, and the


c

will flash amber.

2. Enter the steps for the macro sequence by

pressing the button for the actual command

step. Although the macro may contain up to

19 steps, each button press, including those

used to change devices, counts as a step.

The


c

will flash

green to confirm each button press as you

enter commands.

NOTE:

While entering commands for Power

On/Off of any device during a macro sequence,

press the

Mute Button

. DO NOT press the

actual Power button.

3. When all the steps have been entered,

press the

Sleep Button

j

to enter the

commands. The red light under the

Input

Selectors

ef

will blink and then

turn off.

43

31

43

31

38

PROGRAMMING THE REMOTE

Programming the Remote

Harman Kardon AVR 520 Owners Manual - Page 38

Programming The Remote

Page 38 highlights