Hayward ColorLogic 2.5 Model: Series SP0522 SP0523 SP0530 SP0531 - Page 8

OPERATING INSTRUCTIONS ENGLISH GETTING STARTED Congratulations on your purchase of a Hayward ColorLogic LED Light. Welcome to a more colorful world brought to you by Hayward and Chromacore,R patented technology that generates colored light and effects using a microprocessor to control red, green, and blue LED's. Your Hayward ColorLogic underwater pool or spa light has these features: 1. Long-lasting LED's (light-emitting diodes) which can last up to 10 times longer than current incandescent, halogen, or metalhalide pool and spa lights. 2. Multicolor capability without any color wheels or moving parts to wear out. 3. Multicolor program capability which allows you to select any one of 12 different programs, 5 fixed colors, and 7 color shows. 4. Low power consumption. Uses approximately half of the power needed for an ordinary 100 watt light. OPERATING THE LIGHT Your Hayward ColorLogic light is operated through power-cycling: a method of changing modes which requires no special controller or interface. To activate the light, simply turn on the switch. To deactivate the light, turn off the switch. To advance to the next program, turn the switch off, then back on within 10 seconds. Whenever the light has been off for over 60 seconds, and is first turned on, it will come on to white for 15 seconds for quick clear view of your pool, then go to the last fixed color or color show it was running. LIGHT SYNCHRONIZATION If your pool or spa has multiple Hayward ColorLogic LED lights, they may be operated independently, or they can be easily synchronized so they will all display the same colors and shows at the same time. For light synchronization, all lights must be wired to the same switch. Once installed, all lights should be automatically synchronized, however, if they get out of sync, they can be re-synchronized easily. To re-synchronize your lights, turn the switch on, then back off, then wait between 11 and 14 seconds and turn the switch back on. When the lights come back on, they should enter program #1, and be synchronized. Hayward R is a registered trademark and ColorLogicTM is a trademark of Hayward Pool Products, Inc. Chromacore R is a registered trademark of Color Kinetics, Inc. 2APlal tRenigthst6s,R01e6s,e0r3v8eda.nd 6,150,774 European Patent 1,016,062 Other patents pending. C 2004 Hayward Pool Products, Inc. PROGRAMS Your Hayward ColorLogic light has the capability to display 12 different programs. These programs are advanced using powercycling. The programs are: 1. Show - Voodoo Lounge - Fast Color Wash 2. Fixed - Deep Blue Sea 3. Fixed - Afternoon Skies 4. Fixed - Emerald 5. Fixed - Sangria 6. Fixed - Cloud White 7. Show - Twilight - Slow Color Wash 8. Show - Tranquility - Blue/Cyan/White Fade 9. Show - Gemstone - Blue/Green/Magenta Fade 10. Show - USA! - Red/White/Blue Switch 11. Show - Mardi Gras - Fast Random Fade 12. Show - Cool Cabaret - Slow Random Fade TROUBLESHOOTING If you have a problem with your Hayward ColorLogic light, please try the following tips before calling for service: PROBLEM: Light will not advance to the next show when it is power-cycled (turned "off" and then back "on"). SOLUTION: Do not power-cycle the switch rapidly, leave it off for at least 1 second before turning it back on. PROBLEM: Light goes to white whenever it is power-cycled (turned "off" and then back "on"). SOLUTION: Be sure that you power-cycle the light for less than 10 seconds. PROBLEM: Multiple lights are not correctly synchronized. SOLUTION: Follow the steps in these instructions to resynchronize the lights. PROBLEM: Light will not come on. SOLUTION: Check ground fault and reset if necessary. PROBLEM: Light will not come on or cycles on and off. SOLUTION: Automatic thermal switch may be cycling due to excessive temperatures. Check pool or spa water temperature. PROBLEM: Light does not function properly, or does not function at all. SOLUTION: Verify that your pool/spa controller is not "dimming" the light. HAYWARDR