Hayward HCP Pump HCP Series LITCPOMA10 - Page 6

Nameplate Ratings, Liability, Standards - distributors

Get Hayward HCP Pump PDF manuals and user guides View all Hayward HCP Pump manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Hazardous Pressure. Incorrectly installed or tested equipment may fail, causing severe injury or property damage. Read and follow instructions in owner's manual when installing and operating equipment. 1. Have a trained pool professional perform all pressure tests. 2. Do not connect system to a high pressure or city water system. 3. Use equipment only in a pool or spa installation. 4. Install pump with at least 2 hydraulically balanced main drains equipped with correctly installed, screw-fastened, anti-entrapment certified covers. See pages 14-15. 5. Trapped air in system can cause explosion. BE SURE all air is out of system before operating or testing equipment. Before pressure testing, make the following safety checks: • Check all clamps, bolts, lids, and system accessories before testing. • Release all air in system before testing. • Hand tighten lid bolts. • When pressure testing pumps and strainer listed in this manual, water pressure for test must be less than 40 PSI (2.8 bar). • Water Temperature for test must be less than 100° F (38° C). • Limit test to 24 hours. After test, visually check system to be sure it is ready for operation. Remove trap lid and retighten by hand only. NOTICE These parameters apply to Hayward equipment only. For non-Hayward equipment, consult manufacturer. 2.3 NAMEPLATE RATINGS The information given on the nameplate, or other instructions affixed by the manufacturer to the unit, must be strictly complied with. The content of these plates can be found in this manual under TECHNICAL CHARACTERISTICS, section 1.2; and ELECTRICAL SPECIFICATIONS, section 3.2. 2.4 LIABILITY Failure to comply with the instructions given by the manufacturer in this manual, in relation to the choice, handling, installation, starting and maintenance of the unit, shall release the manufacturer or distributor from all liability in respect of accidents suffered by persons or damages caused to other installations and, in addition, shall entail forfeit of the warranty. 2.5 STANDARDS Our HCP Series pumps are manufactured in accordance with the necessary requirements for safety and health. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
6
Hazardous Pressure. Incorrectly installed or tested equipment may fail,
causing severe injury or property damage.
Read and follow instructions in
owner's manual when installing and operating equipment.
1.
Have a trained pool professional perform all pressure tests.
2.
Do not connect system to a high pressure or city water system.
3.
Use equipment only in a pool or spa installation.
4. Install pump with at least 2 hydraulically balanced main drains equipped
with correctly installed, screw-fastened, anti-entrapment certified covers.
See pages 14-15.
5.
Trapped air in system can cause explosion. BE SURE all air is out of system
before operating or testing equipment.
Before pressure testing, make the following safety checks:
• Check all clamps, bolts, lids, and system accessories before testing.
• Release all air in system before testing.
• Hand tighten lid bolts.
•
When pressure testing pumps and strainer listed in this manual, water pressure for test must be
less than 40 PSI (2.8 bar).
• Water Temperature for test must be less than 100° F (38° C).
• Limit test to 24 hours. After test, visually check system to be sure it is ready for operation.
Remove trap lid and retighten by hand only.
These parameters apply to Hayward equipment only. For non-Hayward equipment,
consult manufacturer.
2.3
NAMEPLATE RATINGS
The information given on the nameplate, or other instructions affixed by the manufacturer to the
unit, must be strictly complied with. The content of these plates can be found in this manual under
TECHNICAL CHARACTERISTICS, section 1.2; and ELECTRICAL SPECIFICATIONS, section 3.2.
2.4
LIABILITY
Failure to comply with the instructions given by the manufacturer in this manual, in relation to the
choice, handling, installation, starting and maintenance of the unit, shall release the manufacturer or
distributor from all liability in respect of accidents suffered by persons or damages caused to other
installations and, in addition, shall entail forfeit of the warranty.
2.5
STANDARDS
Our HCP Series pumps are manufactured in accordance with the necessary requirements for
safety and health.
NOTICE