HP 2000fc HP StorageWorks Simple SAN Connection Manager user guide (5697-0083, - Page 20

Configuring Simple SAN Connection Manager for HP-UX and Emulex HBAs, HP-UX configuration

Get HP 2000fc PDF manuals and user guides View all HP 2000fc manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

4. If the following message appears at the end of the installation, you must restart the computer, otherwise, continue with step 6: New driver and qlremote installed but not active. For new driver and qlremote to be active either: Reboot the system (Mandatory in case of Boot From SAN) or Stop all the applications using QLogic driver. Unload QLogic driver by executing following command: # modprobe -r qla2XXX (ex. qla2300, qla2400) Reload new driver by executing following command: # modprobe -v qla2xxx Start qlremote as follows: # /etc/init.d/qlremote start Rebooting the system will automatically load new driver and start qlremote. 5. To install the Linux driver with Fabric Device Management Interface (FDMI) enabled (by default, FDMI is disabled), issue the following command: # modprobe -v qla2xxx ql2xfdmienable=1 6. To verify that the installation completed, check the FC HBA driver version: a. To ensure that the driver is installed in the correct location, issue the following command: # modinfo qla2xxx The following is returned: Filename: /lib/modules/2.6.9-55.ELsmp/kernel/drivers/scsi/qla2xxx/qla2xxx.ko Version: 8.02.02 653675A771C3619AEEA4E9A b. To verify that the driver is loaded, issue the following command: # lsmod | grep qla2xxx The following is returned: qla2xxx_conf 303752 qla2xxx 982688 scsi_mod 445298 1 0 qla2xxx c. To verify that the correct driver is loaded, issue the following command: # cat /proc/scsi/qla2xxx/* | grep "Driver version" The following is returned: Firmware version: 3.03.25 IPX Driver version: 8.02.02-fo Configuring Simple SAN Connection Manager for HP-UX and Emulex HBAs Simple SAN Connection Manager is compatible with the HP-UX operating system and Emulex HBAs when configured as described in this section. HP-UX configuration Simple SAN Connection Manager can manage all of your supported HP-UX servers. The HP-UX operating system provides native software drivers for the HP StorageWorks FC HBAs. In order for the application to properly identify your server(s), you must manually enter the Fabric Device Management Interface (FDMI) information when the application prompts for it. For details, see "Manually entering FDMI information" on page 81. 20 Installing, upgrading, and removing Simple SAN Connection Manager

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
20
Installing, upgrading, and removing Simple SAN Connection Manager
4.
If the following message appears at the end of the installation, you must restart the computer, otherwise,
continue with
step 6
:
New driver and qlremote installed but not active.
For new driver and qlremote to be active either:
Reboot the system (Mandatory in case of Boot From SAN)
or
Stop all the applications using QLogic driver.
Unload QLogic driver by executing following command:
# modprobe -r qla2XXX (ex. qla2300, qla2400)
Reload new driver by executing following command:
# modprobe -v qla2xxx
Start qlremote as follows:
# /etc/init.d/qlremote start
Rebooting the system will automatically load new driver and start qlremote.
5.
To install the Linux driver with Fabric Device Management Interface (FDMI) enabled (by default, FDMI is
disabled), issue the following command:
# modprobe -v qla2
xxx
ql2
x
fdmienable=1
6.
To verify that the installation completed, check the FC HBA driver version:
a.
To ensure that the driver is installed in the correct location, issue the following command:
# modinfo qla2
xxx
The following is returned:
Filename: /lib/modules/2.6.9-55.ELsmp/kernel/drivers/scsi/qla2
xxx
/qla2
xxx
.ko
Version: 8.02.02 653675A771C3619AEEA4E9A
b.
To verify that the driver is loaded, issue the following command:
# lsmod | grep qla2
xxx
The following is returned:
qla2
xxx
_conf 303752 1
qla2
xxx
982688 0
scsi_mod
445298 qla2
xxx
c.
To verify that the correct driver is loaded, issue the following command:
# cat /proc/scsi/qla2
xxx
/* | grep "Driver version"
The following is returned:
Firmware version: 3.03.25 IPX
Driver version: 8.02.02-fo
Configuring Simple SAN Connection Manager for HP-UX and Emulex
HBAs
Simple SAN Connection Manager is compatible with the HP-UX operating system and Emulex HBAs when
configured as described in this section.
HP-UX configuration
Simple SAN Connection Manager can manage all of your supported HP-UX servers. The HP-UX operating
system provides native software drivers for the HP StorageWorks FC HBAs. In order for the application to
properly identify your server(s), you must manually enter the Fabric Device Management Interface (FDMI)
information when the application prompts for it. For details, see
“Manually entering FDMI information”
on
page 81.