HP 273914-B21 Smart Array 6400 Series Controllers User Guide - Page 23

Configuring the server, In

Get HP 273914-B21 - Smart Array 6404/256 RAID Controller PDF manuals and user guides
UPC - 613326361313
View all HP 273914-B21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

23 Configuring the server In this section Configuring the server ...23 Configuring the server After installing the controller hardware and updating the firmware, use RBSU to configure the server. NOTE: The 2-channel expansion module is a controller in its own right. Thus, the Smart Array 6404 Controller is actually two 2-channel controllers sharing one PCI-X connector. During POST, each component controller loads its own instance of the required driver and sets its own configuration using ORCA. 1. Power up the server. The server runs the POST sequence and briefly displays an RBSU prompt. 2. At the prompt, press the F9 key to start RBSU. 3. Follow the on-screen instructions to configure the server and set the boot controller order. IMPORTANT: The expansion module on the SA6404 controller cannot be used as a boot device. 4. Save the configuration, and exit from the utility. 5. Restart the server for the new settings to take effect. For more information about using RBSU, refer to the HP ROM-Based Setup Utility User Guide or the server setup and installation guide. These documents are both available on the Documentation CD supplied in the server kit.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
23
Configuring the server
In this section
Configuring the server
..................................................................................................................
23
Configuring the server
After installing the controller hardware and updating the firmware, use RBSU to
configure the server.
NOTE:
The 2-channel expansion module is a controller in its own right.
Thus, the Smart Array 6404 Controller is actually two 2-channel
controllers sharing one PCI-X connector. During POST, each
component controller loads its own instance of the required driver and
sets its own configuration using ORCA.
1.
Power up the server.
The server runs the POST sequence and briefly displays an RBSU prompt.
2.
At the prompt, press the
F9
key to start RBSU.
3.
Follow the on-screen instructions to configure the server and set the boot
controller order.
IMPORTANT:
The expansion module on the SA6404 controller cannot
be used as a boot device.
4.
Save the configuration, and exit from the utility.
5.
Restart the server for the new settings to take effect.
For more information about using RBSU, refer to the
HP ROM-Based Setup
Utility User Guide
or the server setup and installation guide. These documents
are both available on the Documentation CD supplied in the server kit.