HP 3PAR StoreServ 7450 4-node HP 3PAR StoreServ 7450 Storage Service Guide
HP 3PAR StoreServ 7450 4-node Manual
View all HP 3PAR StoreServ 7450 4-node manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 3PAR StoreServ 7450 4-node manual content summary:
- HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 1
HP 3PAR StoreServ 7450 Storage Service Guide Abstract This guide provides information about maintenance and upgrading HP 3PAR StoreServ 7450 Storage system hardware components for authorized technicians. HP Part Number: QR482-96304 Published: June 2013 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 2
to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 3
FC) Adapter LEDs 34 Converged Network Adapter (CNA) LEDs 35 Node FC and CNA Port Numbering 35 SAS Port LEDs...36 Interconnect Port LEDs...37 Verifying Service Processor LEDs 37 3 Support and Other Resources 40 Contacting HP...40 HP 3PAR documentation...40 Typographic conventions...43 Contents 3 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 4
branding information 43 4 Documentation feedback 44 A Installing Storage Software Manually 45 Connecting to the Laptop...45 Connecting the Laptop to the Controller Node 45 Connecting the Laptop to the HP 3PAR Service Processor 45 Serial Cable Connections...45 Maintenance PC Connector Pin-outs - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 5
and replacement procedures on the HP 3PAR StoreServ 7450 Storage systems. : Before servicing any component in the storage Guided Maintenance or the SPMAINT (Service Processor Maintenance) in the Command Line Interface (CLI), where you perform various administrative and diagnostic tasks to support - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 6
for self repair. For assistance, contact an HP-authorized service provider to replace the part. These parts include the drive and node enclosures, the I/O modules, PCMs, and internal components of the controller node in the HP 3PAR StoreServ 7450 systems. Types of CSR components include: • Disk - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 7
Figure 2 Product label with HP Spare part number Swappable Components Colored touch points on a storage in the enclosure until the replacement can be made. Drives must be replaced within 10 minutes, nodes 30 minutes and all other parts within 6 minutes. • Before replacing a hot-swappable component, - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 8
Guided Troubleshooting web site, follow the link for your product. 3. At the bottom of the HP 3PAR product page, click the link for HP 3PAR Alert Messages. 4. At the bottom of the Alert Messages page, choose the correct message code series based SPOCC, see "Service Processor Onsite all node and - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 9
This can seriously impact host access to data. 3. Turn off power to the node PCMs. 4. Turn off power to the drive enclosure PCMs. 5. Turn off all Pivot Brackets To access the vertically mounted power distribution units (PDU) or servicing area, the PDUs can be lowered out of the rack. 1. Remove the - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 10
node enclosure PCMs. 10. Verify the status of the LEDs, see "Understanding LED Indicator Status" (page 26). Repairing a Disk Drive Use the following instructions for replacing failed disk drives or solid-state drives (SSD). WARNING! If the StoreServ fault LED is lit. 10 Servicing the Storage System - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 11
service life of an HP 3PAR StoreServ under the great majority of configurations, input/output patterns, and workloads. HP 3PAR StoreServ HP support contracts. Identifying a Disk Drive 1. Under the Systems tree in the left panel of HP 3PAR Management Console, select the storage system to be serviced - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 12
Failed drive (see Figure 8 (page 12)). Figure 8 Cage Link for Failed Drive 3. Select the Locate icon in the top toolbar of the Management Console. 12 Servicing the Storage System - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 13
Figure 9 Tool Bar Locate Icon 4. In the Locate Cage dialog box, enter an appropriate time to allow service personnel to view the LED status of the Drive Enclosure (Cage). See Figure 10 (page 13). NOTE: If necessary, use the Stop Locate icon to - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 14
Figure 11 7450 Two Node System (HP M6710 Drive Enclosure) Removing a 3.5 inch Disk To remove a 3.5 inch disk drive: 1. Pinch the latch in the handle towards To reinstall a new disk drive, see "Installing a Disk Drive" (page 15). Figure 12 Removing a 3.5 inch disk drive 14 Servicing the Storage System - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 15
based on drive type, speed, and capacity. For more information, see "Guidelines for Installing Disk Drives and Disk Enclosures" in the HP 3PAR StoreServ 7450 Storage Installation Guide ; push firmly until it clicks. Figure 13 7450 Two Node System (HP M6710 Drive Enclosure) Installing a 3.5 inch disk - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 16
resort. NOTE: Until data has been restored, the original disk drive will display as Failed and the replacement disk drive will display as Degraded. 16 Servicing the Storage System - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 17
, which may take several hours. When the process is complete, the failed drive is dismissed and dropped from the display. Disk Drive Numbering Figure 15 7450 2-Node - displayed as DCN1 in software output Figure 16 7450 4 Controller Node Displayed as DCN1 in Software Output Repairing a Disk Drive 17 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 18
that the component is warm-swappable. HP recommends that the node be shutdown (with the power remaining on) before removing this component. Contact your ASP for node diagnosis and shutdown. CAUTION: To prevent overheating, node replacement requires a maximum service time of 30 minutes. NOTE: Be - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 19
the failed node. 4. Pull the gray node rod to remove the node from the enclosure. 5. When the node is halfway out of the enclosure, use both hands to slide the node out completely. 6. Set the node on the ESD safe mat next to the replacement node for servicing. 7. Push in the failed node's grey rod - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 20
that the node has joined the cluster. 9. Follow the return instructions provided with the new component. NOTE: If a PCIe adapter is installed in the failed node, leave it installed. Do not remove and return it in the packaging for the replacement PCIe adapter. 20 Servicing the Storage System - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 21
HBA/CNA and there are two to six SFPs per node. Before you begin, use either SPMAINT or the HP 3PAR Management Console to identify the failed SFP. SFP Identification 1. Under the Systems tree in the left panel, select the storage system to be serviced. 2. On the Summary tab, click the Port link to - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 22
be listed as Ready, the Mode as Target and the Connected Device Type as Host. To perform maintenance using CLI, access SPMAINT: 1. In the 3PAR Service Processor Menu, select option 7 Interactive CLI for an InServ. 2. Issue the following commands: • showport to view the port State: s750 cli%showport - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 23
to verify which SFP requires replacement: cli%showport -sfp N:S:P -State- -Manufacturer- MaxSpeed(Gbps) TXDisable TXFault RXLoss DDM 0:1:1 OK HP-F 8.5 No No No Yes 0:1:2 OK HP-F 8.5 No No No Yes 0:2:1 OK AVAGO 10.3 No No Yes Yes 0:2:2 OK AVAGO 10.3 No No Yes Yes 1:1:1 OK - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 24
No Yes 1:2:1 OK HP-F 8.5 No No Yes Yes 1:2:2 OK HP-F 8.5 No No Yes Yes 1:2:3 OK HP-F 8.5 No No Yes Yes 1:2:4 OK HP-F 8.5 No No Yes Yes Open the HP 3PAR Management Console 1. Under the Systems tree in the left panel, select the storage system to be serviced to connect. 2. On - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 25
SFP. See "Replacing an SFP" (page 25). 6. In the HP 3PAR Management Console, verify that the SFP is successfully replaced. The replaced the cable. 4. Place the failed SFP into the packaging for return to HP. 5. Reconnect the cable to the SFP module and verify that the link status LED is solid green - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 26
LEDs to indicate status of the hardware and whether it is functioning properly. These indicators help diagnose basic hardware problems. You can quickly identify hardware problems by examining the LEDs on all components using the tables and illustrations in this chapter. Enclosure LEDs Bezels LEDs - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 27
Figure 25 Disk Drive LEDs Table 2 Disk drive LEDs LED 1 - Fault Appearance Amber 2 - Activity Green Status On Flashing On Flashing Indicates Disk failed and is ready to be replaced. The locatecage command has been issued. Fault LEDs for failed disk drives do not blink. The I/O module Fault - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 28
Figure 26 PCM LEDs The following table describes the LED states. Table 3 PCM LED Descriptions Icon LED Appearance On AC input fail Amber Flashing Indicates No AC power or PCM fault Firmware download PCM OK Green On Flashing AC present and PCM On / OK Standby mode Fan Fail Amber On - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 29
Table 3 PCM LED Descriptions (continued) Icon LED Appearance On Battery Good Green Flashing Indicates Present and charged Charging or disarmed Drive PCM LEDs The following figure shows the drive enclosure PCM LEDs. Figure 27 Drive PCM LEDs The next table describes the drive PCM LED states. - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 30
Table 4 Drive PCM LED Descriptions (continued) Icon LED Appearance On DC Output Fail Amber Flashing Indicates No AC power or fault or out of tolerance Firmware download I/O Modules LEDs I/O modules are located on the back of the system. I/O modules have two mini-SAS universal ports, which - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 31
command issued Function External Port Activity; 4 LEDs for Data Ports 0 through 3 Appearance Green State On Off Flashing Controller Node and Internal Component LEDs Controller node LEDs are shown in the following table. Meaning Ready, no activity Not ready or no power Activity Controller - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 32
Figure 32 Controller Node LEDs NOTE: Issue the locatenode command to flash the hotplug LED blue. Figure 33 Controller Node Indicator LEDs Table 6 Controller Node LEDs Status Green On Quick Flashing Slow Flashing Not a Cluster member Boot Cluster member 32 Understanding LED Indicator Status - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 33
Off Flashing 1 Gbe Link 100 Mbit Link No link established or 10 Mbit Link No link activity No link established Link activity Node FC and CNA Port LEDs The controller node has two FC ports; each includes two LEDs. The arrow head-shaped LEDs point to the port they are associated with - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 34
Figure 35 FC Port LEDs Table 8 FC Port LEDs All ports FC-1 No light Amber FC-2 Green Off Off 3 fast blinks 4 fast blinks On Flashing Fibre Channel (FC) Adapter LEDs Figure 36 FC Adapter LEDs Wake up failure (dead device) or power is not applied Not connected Connected at 4GB/sec. Connected - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 35
CNA LEDs Upper Link Lower ACT (Activity) Green Green Off Link down On Link up Off No activity On Activity Node FC and CNA Port Numbering Port position is displayed as Node:Slot:Port (N:S:P) in the Management Console. Figure 38 FC Ports Table 11 FC Ports Port FC-1 FC-2 Figure 39 FC - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 36
Table 12 FC Adapter Ports Port 1 2 3 4 Figure 40 CNA Ports Slot:Port 2:1 2:2 2:3 2:4 Table 13 CNA Ports Port 1 2 Slot:Port 2:1 2:2 SAS Port LEDs The controller node has two SAS ports and each includes four LEDs, numbered 0-3: Figure 41 SAS port LEDs 36 Understanding LED Indicator Status - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 37
. Figure 42 7450 Interconnect Ports LEDs Figure 43 7450 Interconnect Ports LEDs Table 15 Interconnect port LEDs 7450 Fault Status Amber node in wrong slot 3. Serial number mismatch between controller nodes Link established Link not yet established Verifying Service Processor LEDs The HP 3PAR - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 38
Figure 44 Front Panel LEDs Table 16 Front panel LEDs Item LED 1 UID LED/button 2 Power On/Standby button and system power Appearance Blue Flashing Blue Off Green Flashing Green Amber Off 3 Health Green 4 NIC status Figure 45 Rear Panel LEDs Flashing Amber Flashing Red Off Green Flashing Green - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 39
Off = one or more of the following conditions: • Power is unavailable • Power supply has failed • Power supply is in standby mode • Power supply error Verifying Service Processor LEDs 39 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 40
number or Service Agreement ID (if applicable) • Product serial numbers • Error messages • Operating system type and revision level • Detailed questions Specify the type of support you are requesting: HP 3PAR storage system HP 3PAR StoreServ 7450 Storage systems HP 3PAR StoreServ 10000 Storage - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 41
, and detailed alert information HP 3PAR F-Class, T-Class, and StoreServ 10000 Storage Troubleshooting Guide Installing, configuring, and maintaining the HP 3PAR Policy HP 3PAR Policy Server Installation and Setup Guide Server HP 3PAR Policy Server Administration Guide HP 3PAR documentation 41 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 42
Service Processor HP 3PAR StoreServ 7450 Storage Installation Guide HP 3PAR StoreServ 7450 Storage SmartStart Software User's Guide Maintaining, servicing, and upgrading 7450 storage systems HP 3PAR StoreServ 7450 Storage Service Guide Troubleshooting 7450 storage systems HP 3PAR StoreServ 7450 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 43
followed as directed in order to achieve a functional and supported implementation based on testing at HP. HP 3PAR branding information • The server previously referred to as the "InServ" is now referred to as the "HP 3PAR StoreServ Storage system." • The operating system previously referred to as - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 44
documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback ([email protected]). Include the document title and part number, version number, or the URL when submitting your feedback. 44 Documentation feedback - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 45
or SPOCC to perform maintenance procedures. For more information on servicing the storage system, see the HP 3PAR StoreServ 7450 Storage Service Guide. Connecting the Laptop to the Controller Node Connect the RJ45 cable to the controller node MFG ports (known as the public interface) to the laptop - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 46
Laptop to the SP" in the HP 3PAR StoreServ 7450 Storage Installation Guide. Manually Setting up the Storage System The Out-of-the-Box (OOTB) script guides you through setting up and configuring the storage system software: 1. Connect the PC to the controller node 0 through a serial cable and log in - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 47
is in a proper manual startup state to proceed. Cluster has the following nodes: Node 0: Node 1: ... Is this nodes in the system, then type c and press Enter. If the system is not ready for the system setup script, an error message appears. After following any instructions and correcting any problems - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 48
as directed. CAUTION: HP recommends that at least four physical disks worth of chunklets be designated as spares to support the servicemag command. The the exact number of chunklets, but is not recommended as spares must be manually added when new disks are added. Enter "Ma" for maximal, "D" for - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 49
local service provider for technical support to nodes to use for each address. Note, are nodes (for example: 2 3 for nodes 2 and 3). Enter config for IP #0 IP Address: Netmask: Nodes HP 3PAR Service Processor Software 4.1.0 MU2, the SP Setup Wizard expects the StoreServ - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 50
1 for SP Control/Status. 1 SP Main 3PAR Service Processor Menu Transfer media: ethernet Transfer status: Ok Display SP Version SP Software Version SP-2.5.1.GA-15 SP Base Image Version: 3.1-8 SP Version: 2.5.1.GA-15 SP Service Processor" (page 51). 50 Installing Storage Software Manually - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 51
the maintenance PC to the SP. 2. In the SPMaint, type 3 and press Enter to select InServ Configuration Management. SPXXXXX 1 SP Main 3PAR Service Processor Menu Transfer media: ethernet Transfer status: No transfer yet Enter Control-C at any time to abort this process 1 ==> SP Control/Status - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 52
3PAR system name found for SYSID found for serial number found for Writing configuration file for ... verifying / adding cli service the HP 3PAR Implementation Guides where - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 53
node, PCI slot, and PCI adapter port to be controlled. 5. When finished setting each connected target port, verify that all ports are set correctly. 192.168.46.249 cli% showport -par Creating and Exporting Test Volumes For more information about the commands used in this section, see the HP 3PAR - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 54
port on the laptop. 3. Access SPmaint and in the 3PAR Service Processor Menu, select the following: • 4 InServ Product Maintenance • 11 Node Rescue • 1 Configure Node Rescue, then select the desired system • 3 Automatic Node Rescue, then enter the node number 4. Select y to confirm the correct - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 55
system 7. Issue the following commands: • shownode to verify that all nodes have joined the cluster. cli% shownode Control Data Cache Node Name -State- Master InCluster --LED-- Mem(MB) Mem(MB) . 8. Click the SPmaint menu button, then click Sign Out. Service Processor (Physical) Node Rescue 55 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 56
component of the storage system for all replaceable hardware parts including the part number, full description, quantity, and CSR type. Drive Enclosure Components Figure 48 HP M6710 Drive Enclosure (2U24) Figure 49 HP M6720 Drive Enclosure (4U24) 56 Illustrated Parts Catalog - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 57
Figure 50 2.5-inch SFF disk drive Figure 51 3.5-inch LFF disk drive Table 19 Drive Chassis FRUs Material Number Description Qty Per Chassis 683232-001 SPS-Enclosure Midplane 2U24 Assy 1 683233-001 SPS-Enclosure Midplane 4U24 Assy 1 683234-001 SPS-Drive Carrier SFF SSD Assy 683235-001 SPS - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 58
) Material Number Description Qty Per Chassis 727395-001 HP M6710 400GB 6G SAS 2.5in MLC SSD (7450 systems only) 727396-001 HP M6720 400GB 6G SAS 3.5in MLC SSD (7450 systems only) 727390-001 HP M6710 400GB 6G SAS 2.5in MLC Encr SSD (7450 systems only) Storage System Components Figure 52 764 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 59
Figure 54 580 W Power Cooling Module Figure 55 I/O Module Table 20 Storage System Components Part Number 683239-001 727386-001 683240-001 683241-001 683251-001 Description SPS-PCM 764W Assy SPS-PCM 764W Assy, Gold SPS-Battery PCM 764W Assy SPS-PCM 580W Assy SPS-Module I/O SASquatch Qty. up to 2 - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 60
Controller Node and Internal Components Figure 56 Controller Node Figure 57 Node Disk Figure 58 4-port Fibre Channel Adapter 60 Illustrated Parts Catalog - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 61
Figure 59 2-port CNA Adapter Figure 60 FC SFP Adapter Table 21 Controller Node and Components Part Number Description 727388-001 683248-001 683259-001 683237-001 468508-002 SPS-Node Module 7450 NO HBA SPS-Node Boot Drive (Node drive) SPS-Adapter FC 4port SPS-Adapter CNA 2port SPS-Module FC SFP - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 62
Drive SATA 1 SPS-Cable Boot Drive (Node drive cable) 3 683247-001 SPS-PCIe Riser Assy 1 4 N/A N/A N/A 5 N/A N/A N/A 6 683249-001 SPS-Battery Coin (TOD battery) 1 7 727389-001 SPS-Memory DIMM 16GB DDR3 1 Control Cache 7450 62 Illustrated Parts Catalog CSR Type Not Not N/A N/A Not - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 63
Qty HP 3PAR Service Processor DL320e 1 Miscellaneous Cables and Parts Table 24 Storage System Cables Part Number 683808-001 683809-001 683810-001 683252-001 656427-001 656428-001 656429-001 656430-001 656431-001 656432-001 649991-001 Description Qty. SPS-Cable Node Link PCIe 7450 SPS - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 64
, right 683258-001 SPS-Bezel 7450, left 690777-001 SPS-Bezel M6720 drive shelf, right 690778-001 SPS-Bezel M6710 drive shelf, left 683807-001 SPS-Drive blank SFF 697273-001 SPS-Drive blank LFF Table 26 Service Processor Parts Part Number 683811-001 675040-001 647980-001 Description Qty - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 65
Processor Parts (continued) Part Number Description Qty. 707989-001 SPS-Service Processor DL360e 5183-2687 Ethernet Cable 25 ft CAT5 M/M 5183-5691 Ethernet Cable 50 ft. CAT5 RJ45 M/M C7542A HP Ethernet 15.2m (50 ft) CAT5e RJ45 M/M Cable CSR Type Not Mandatory Miscellaneous Cables - HP 3PAR StoreServ 7450 4-node | HP 3PAR StoreServ 7450 Storage Service Guide - Page 66
in disk drives - showpd • Storage system hardware configuration • Number of enclosures and nodes • Physical condition of system hardware and cabinet (note presence of scratches, dents, component removal procedures in "Servicing the Storage System" (page 5). 66 Uninstalling the Storage System
HP 3PAR StoreServ 7450 Storage Service
Guide
Abstract
This guide provides information about maintenance and upgrading HP 3PAR StoreServ 7450 Storage system hardware
components for authorized technicians.
HP Part Number: QR482-96304
Published: June 2013