HP 8730w HP EliteBook 8730w Mobile Workstation - Maintenance and Service Guide - Page 51

Remove the Torx T8M2.5×6.0 screw, that secures the display inverter or ambient light sensor

Get HP 8730w - EliteBook Mobile Workstation PDF manuals and user guides
UPC - 884962212455
View all HP 8730w manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

3. Remove the six screw covers (1) and six Torx T8M2.5×6.0 screws (2) that secure the display bezel to the display enclosure. 4. Flex the display bezel bottom edge (1), the inside edges of the left and right sides (2), and then the display bezel top edge (3) until the bezel disengages from the display assembly. 5. Lift the display bezel straight up (4) to remove it from the display assembly. NOTE: There are two posts that protrude through two holes on the top edge of the bezel. So that you do not break the posts, be sure to lift the bezel straight up when removing it from the display assembly. 6. Remove the Torx T8M2.5×6.0 screw (1) that secures the display inverter or ambient light sensor to the display enclosure. 7. Release the inverter or sensor (2) from the display enclosure as far as the display panel cable and/ or backlight cable allow. NOTE: Models with a DreamColor LED display use the ambient light sensor which does not have a backlight cable connector. Component replacement procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
3.
Remove the six screw covers
(1)
and six Torx T8M2.5×6.0 screws
(2)
that secure the display bezel
to the display enclosure.
4.
Flex the display bezel bottom edge
(1)
, the inside edges of the left and right sides
(2)
, and then the
display bezel top edge
(3)
until the bezel disengages from the display assembly.
5.
Lift the display bezel straight up
(4)
to remove it from the display assembly.
NOTE:
There are two posts that protrude through two holes on the top edge of the bezel. So that
you do not break the posts, be sure to lift the bezel straight up when removing it from the display
assembly.
6.
Remove the Torx T8M2.5×6.0 screw
(1)
that secures the display inverter or ambient light sensor
to the display enclosure.
7.
Release the inverter or sensor
(2)
from the display enclosure as far as the display panel cable and/
or backlight cable allow.
NOTE:
Models with a DreamColor LED display use the ambient light sensor which does not have
a backlight cable connector.
Component replacement procedures
43