HP Cisco Nexus 5000 Cisco MDS 9000 Family MIB Quick Reference (OL-18087-01, Fe - Page 35

Cisco-flexattach-mib, Cisco-fspf-mib, Cisco-hc-alarm-mib, Cisco-ietf-ip-forward-mib

Page 35 highlights

Send documentation comments to [email protected] CISCO-FLEXATTACH-MIB This MIB enables the automatic generation of virtual WWNs on all of the Fport interfaces whose fcIfOperMode is 'fPort'. The Nxports register with the Fxports with a port WWN as indicated by object fcNameServerPortName in the CISCO-NS-MIB. Generally, the Nxports are zoned with other devices which they need to communicate using this port WWN. However, if the device containing Nx port has to be replaced, zoning has to be reconfigured using the port WWN of the new device to eliminate the need for a zoning change, a special WWN is assigned to the corresponding Fport and the original port WWN is replaced with this special WWN for any device that is logging through the Fport. In addition, the zoning is configured using the special WWN. CISCO-FSPF-MIB This MIB configures and monitors the Fabric Shortest Path First (FSPF) parameters on all VSANs configured on the local switch. FSPF is the protocol currently standardized by the T11 committee for routing in Fibre Channel networks. Refer to http://www.t11.org. CISCO-HC-ALARM-MIB This MIB defines RMON-MIB(RFC 2819) extensions for high-capacity alarms. This MIB is based on the Internet Draft (draft-ietf-rmonmib-hc-alarm-mib-02.txt). In terms of object syntax and semantics, the content of this Cisco MIB is the same as the corresponding Internet Draft revision. This Cisco MIB was created because of the "subject to change" nature of Internet Drafts. This Cisco MIB eventually maybe replaced by a stable RFC. This MIB configures RMON alarms that require high-capacity counters (64-bit counters). CISCO-IETF-IP-FORWARD-MIB This MIB was extracted from the draft-ietf-ipngwg-rfc2096-update-00.txt. In terms of object syntax and semantics, the content of this Cisco MIB is the same as the corresponding I-D revision. This Cisco MIB is created due to the "subject to change" nature of the I-Ds. This Cisco MIB may later be deprecated, and the stable RFC, which may replace the I-D, may be implemented in its place. Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA © Cisco Systems, Inc. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

Send documentation comments to [email protected]
Americas Headquarters:
© <2009> Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706
USA
CISCO-FLEXATTACH-MIB
This MIB enables the automatic generation of virtual WWNs on all of the Fport interfaces whose
fcIfOperMode is 'fPort'.
The Nxports register with the Fxports with a port WWN as indicated by object fcNameServerPortName
in the CISCO-NS-MIB. Generally, the Nxports are zoned with other devices which they need to
communicate using this port WWN. However, if the device containing Nx port has to be replaced, zoning
has to be reconfigured using the port WWN of the new device to eliminate the need for a zoning change,
a special WWN is assigned to the corresponding Fport and the original port WWN is replaced with this
special WWN for any device that is logging through the Fport. In addition, the zoning is configured using
the special WWN.
CISCO-FSPF-MIB
This MIB configures and monitors the Fabric Shortest Path First (FSPF) parameters on all VSANs
configured on the local switch. FSPF is the protocol currently standardized by the T11 committee for
routing in Fibre Channel networks. Refer to
.
CISCO-HC-ALARM-MIB
This MIB defines RMON-MIB(RFC 2819) extensions for high-capacity alarms. This MIB is based on
the Internet Draft (draft-ietf-rmonmib-hc-alarm-mib-02.txt). In terms of object syntax and semantics,
the content of this Cisco MIB is the same as the corresponding Internet Draft revision. This Cisco MIB
was created because of the “subject to change” nature of Internet Drafts. This Cisco MIB eventually
maybe replaced by a stable RFC.
This MIB configures RMON alarms that require high-capacity counters (64-bit counters).
CISCO-IETF-IP-FORWARD-MIB
This MIB was extracted from the draft-ietf-ipngwg-rfc2096-update-00.txt. In terms of object syntax and
semantics, the content of this Cisco MIB is the same as the corresponding I-D revision. This Cisco MIB
is created due to the “subject to change” nature of the I-Ds. This Cisco MIB may later be deprecated,
and the stable RFC, which may replace the I-D, may be implemented in its place.