Home » HP Manuals » Computer Monitors » HP DreamColor Z31x » Manual Viewer

HP DreamColor Z31x User Guide - Page 101

Setting dashboard security, Display Info, Open Menu, Management, Remote management services, Select

Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

NOTE: If the bezel button menu assigned by default to Display Info has been changed, you can also access the Information menu via the Main menu. You can also assign a static IP address to the display, as follows: 1. Press one of the front bezel buttons to display the button labels, and then press the Open Menu button to open the OSD. 2. Select Management. 3. Select Remote management services, and then press Select to open it. 4. Select IP configuration mode, and then press Select to open it. 5. Choose Manual, and then press Select to switch to static IP address mode. The IPv4 Address, Subnet Mask, and Gateway options become active and the cursor jumps to the first entry in the IPv4 Address. 6. Use the bezel buttons to enter the required Address, Subnet Mask, and Gateway numbers. The bezel buttons allow you to increase or decrease the numerical value of entry and move between entries. 7. Press Back when you have completed the IP address configuration. Setting dashboard security By default, the web dashboard only requires a password. The default password is "DreamColor", and you can reset it when you first log in to the dashboard. If you forget the password, you can reset it to "DreamColor" from the Remote management services menu. To reset the default password: 1. Press one of the front bezel buttons to display the button labels, and then press the Open Menu button to open the OSD. 2. Select Management. 3. Select Remote management services. 4. Select Reset administrator password. 5. Select OK to reset the password to 'DreamColor'. You can also require the use of user digital certificates. Any properly issued digital certificate works with the display. Certificates require that users connecting to the display know the display password and have the correct certificate stored in their computer. Additional steps are required to use certificates. You must first request and receive a unique digital certificate, either from your IT department or a certificate authority on the Internet. Once you have a certificate, install it on the computer you use to connect to the display. Refer to your operating system help or documentation for information on how to install certificates. Then set the display to use certificates, and install the same certificate on the display. To configure the display to use certificates and to install a certificate on the display: 1. Press one of the front bezel buttons to display the button labels, and then press the Open Menu button to open the OSD. 2. Select Management. 3. Select Remote management services. Configuring remote management 91

Section	Page
Getting Started	11
Important safety information	11
Product features and components	12
Features	12
Front panel controls	13
Rear and side components	14
Setting up the display	15
Use caution when setting up the display	15
Installing the display stand	15
Mounting the display	16
Locating the serial number and product number	17
Attaching an optional device to the rear of the display	18
Installing a security cable	18
Connecting the cables	19
Adjusting the display	23
Turning on the display	24
HP watermark and image retention policy	25
Connecting USB devices	25
Removing the display stand	26
Using the display	27
Software and utilities	27
The information file	27
The image color matching files	27
Installing the .INF and .ICM files	28
Installing from the disc	28
Downloading from the Internet	28
Updating the firmware	28
Selecting a color space preset	30
Adjusting luminance	30
Understanding image adjustment options	31
Video signal adjustments	31
Downstream RGB adjust	31
Use video levels (64–960)	31
Overscan the frame	32
Show only the blue channel	32
Using the aspect ratio management options	32
The “Fill To” options	32
Fill to source aspect ratio (proportional)	33
Fill to entire screen (non-proportional)	33
Fill to screen width (proportional)	33
Fill to screen height (proportional)	34
Pixel-for-pixel	35
True 2K pixel mapping	35
Using the “fill To” options	35
Digital cinema aspect ratio masking	36
Using the digital cinema aspect ratio masking options	36
Show entire DCI container	36
Mask to DCI 1.85:1 aspect ratio	36
Mask to DCI 2.39:1 aspect ratio	38
Show masked region	38
Set mask opacity	38
Working with markers	39
Film aspect ratio markers	39
16:9 aspect ratio markers	40
4:3 aspect ratio markers	41
Crosshair markers	42
Marker color	42
Custom markers	42
Marker element	42
Marker info element	43
Marker position element	43
Marker style element	43
Custom marker example	44
Using picture-in-picture (PIP) and 2×1 dual split	44
Adjusting the PIP image	45
Video legal (64–960)	45
Overscan to safe action	45
Digital cinema cropping	45
Renaming video inputs	45
Custom video input names	45
Video input element	46
Input info element	46
Custom video input name example	46
Using the KVM switch	46
How to connect computers to the display	47
How to bind the USB inputs to the video connections	47
To switch between connected computers	47
Customizing bezel buttons	48
Changing the bezel function buttons	48
Changing the bezel function button mode	49
Adjusting the bezel button LEDs	49
User presets	50
Creating and saving a user preset	51
Activating a user preset	51
Migrating user presets between displays	52
User presets element	52
User preset file	52
User preset example	52
Automatic input-based presets	52
Navigating the on-screen display menus	53
Color settings menu	53
Video input menu	55
Image adjustment menu	56
Split/PIP control menu	57
Load/save user preset	59
Calibration	59
Language menu	60
Management menu	61
Menu and message control menu	65
Information	66
Auto EDID update	67
Display calibration	68
Factory calibration	68
Preparing for calibration	68
Enabling the internal processor	68
Enabling calibration and external instruments	69
Calibration environment	69
Calibration frequency	70
Display warm-up from cold power on	70
Warm-up mode	71
Backlight stabilization after luminance change	71
User calibration methods	71
Menu-driven user calibration	72
Recalibration active preset	72
Configure and calibrate preset	72
Color preset	72
Color gamut	72
White point	73
Gamma/EOTF	73
Luminance	73
StudioCal XML calibration	74
Calibration automation	74
Scheduling automated calibrations	74
Viewing the calibration schedule	75
Using a StudioCal XML file for automation	75
Accessing automatic calibration validation information	75
Aligning the internal colorimeter to an external reference instrument	76
Automatically warming up the display at start of the day	76
Using external measurement instruments	77
Klein Instruments K10 and K10-A colorimeters	77
Configuration	77
Usage guidelines	78
Photo Research spectroradiometers	78
Configuration	78
Usage guidelines	79
Konica Minolta CA-310 colorimeter	79
Configuration	79
Usage guidelines	79
X-Rite i1Pro 2 spectrophotometers	80
Configuration	80
Usage guidelines	80
X-Rite i1Display Pro colorimeter	80
Configuration	80
Usage guidelines	80
Colorimetry Research CR-250 spectroradiometer	81
Configuration	81
Usage guidelines	81
Using the StudioCal XML schema	82
File name and disk format	82
Declaration	82
Comments	82
Root element	82
Calibration element	83
Calibration info element	83
Core calibration tags	83
Preset	83
Target_primaries	84
Gamma	85
Core calibration tag examples	85
ICC profile generation	86
Optional calibration tags	87
Measurement averaging	87
Set linear segment	87
Select Klein cal file	87
Contrast ratio limiting	87
Validation	88
Validation on/off	88
Validation pattern parent element	88
Validation pattern child element	88
Validation code example	88
Validation results file	89
LUT archiving, downloading and uploading	90
Archive LUT	90
Download LUT	90
Download LUT parent element	90
Download LUT child element	90
Download LUT example	91
Upload LUT	91
Upload LUT parent element	91
Upload LUT child element	91
Upload LUT example	92
LUT folder structure	92
Using non-supported measurement equipment	93
Making measurements with non-supported measurement equipment	94
Non-calibration elements	95
Custom video input names	95
Video input element	95
Input info element	95
Custom video input name example	96
Custom markers	96
Marker parent element	96
Marker info parent element	96
Marker position element	96
Marker style element	97
Custom marker example	97
User presets	98
User presets element	98
User preset file	98
User preset example	98
Display settings uploading and downloading	98
Remote management	100
Configuring remote management	100
Turning remote management on	100
Checking and setting the display’s IP address	100
Setting dashboard security	101
Logging in to the web dashboard for the first time	102
Logging into the web dashboard	102
Navigating the dashboard	103
Navigating between the different dashboard sections	103
Logging out of the dashboard	103
Support and troubleshooting	104
Solving common problems	104
Button lockouts	104
Product support	105
Preparing to call technical support	105
Maintaining the display	106
Maintenance guidelines	106
Cleaning the display	106
Shipping the display	106
Technical specifications	107
Preset display resolutions	108
Entering user modes	110
Energy saver feature	110
Accessibility	111
Supported assistive technologies	111

Match case Limit results 1 per page

NOTE:

If the bezel button menu assigned by default to

Display Info

has been changed, you can also access

the Information menu via the

Main

menu.

You can also assign a static IP address to the display, as follows:

Press one of the front bezel buttons to display the button labels, and then press the

Open Menu

button

to open the OSD.

Select

Management

Select

Remote management services

, and then press

Select

to open it.

Select

conﬁguration

mode

, and then press

Select

to open it.

Choose

Manual

, and then press

Select

to switch to static IP address mode.

The

IPv4 Address

Subnet Mask

, and

Gateway

options become active and the cursor jumps to the

ﬁrst

entry in the

IPv4 Address

Use the bezel buttons to enter the required Address, Subnet Mask, and Gateway numbers.

The bezel buttons allow you to increase or decrease the numerical value of entry and move between

entries.

Press

Back

when you have completed the IP address

conﬁguration.

Setting dashboard security

By default, the web dashboard only requires a password. The default password is “DreamColor”, and you can

reset it when you

ﬁrst

from the

Remote management services

menu.

To reset the default password:

Press one of the front bezel buttons to display the button labels, and then press the

Open Menu

button

to open the OSD.

Select

Management

Select

Remote management services

Select

Reset administrator password

Select

to reset the password to ‘DreamColor’.

You can also require the use of user digital

certiﬁcates.

Any properly issued digital

certiﬁcate

works with the

display.

Certiﬁcates

require that users connecting to the display know the display password and have the

correct

certiﬁcate

stored in their computer.

Additional steps are required to use

certiﬁcates.

You must

ﬁrst

request and receive a unique digital

certiﬁcate,

either from your IT department or a

certiﬁcate

authority on the Internet.

Once you have a

certiﬁcate,

install it on the computer you use to connect to the display. Refer to your

operating system help or documentation for information on how to install

certiﬁcates.

Then set the display to

use

certiﬁcates,

and install the same

certiﬁcate

on the display.

conﬁgure

the display to use

certiﬁcates

and to install a

certiﬁcate

on the display:

Press one of the front bezel buttons to display the button labels, and then press the

Open Menu

button

to open the OSD.

Select

Management

Select

Remote management services

Conﬁguring

remote management