Home » HP Manuals » Servers » HP Integrity Superdome 2 16-socket » Manual Viewer

HP Integrity Superdome 2 16-socket HP Superdome 2 Partitioning Administrator G - Page 25

Operating system specific default values for nPartition attributes, support for a new

View all HP Integrity Superdome 2 16-socket manuals

Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

ILM granule size at next boot SLM granule size SLM granule size at next boot Max number of ILM granules possible Max number of SLM granules possible User Specified Max number of blades Max number of blades at next boot User Specified Max number of vpars Max number of vpars at next boot Current boot mode Next boot mode Parspec Change Policy VGA VGA next boot mode Pending Deletion : 1024 MB : 1024 MB : 1024 MB : 1024 : 1024 : 8 : 8 : 16 : 16 : npars : npars : Enabled : Enabled : Enabled : - parstatus -C [Blade] Enclosure/ Usage/ Blade Status* === 1/5 InActive Base/OK 1/7 Inactive Base/OK CPU OK/ Indicted/ Deconf Max ======= 8/0/0/8 8/0/0/8 Memory (GB) Use Par Pending (GB) On Num Deletion OK/ Next Indicted/ Boot Deconf 16.0/0.0/0.0 yes 2 - 16.0/0.0/0.0 yes 2 - * D-Degraded I-Indicted NOTE: On SD2, for an nPar in npar mode, nPars are created with a default ILM/SLM distribution of 1:7 when no value is specified for SLM. For an nPar created in vpar mode, the default is to use 100% ILM. Operating system specific default values for nPartition attributes When an nPartition is created for a specific operating system type, the default values specific to that operating system type are applied to the nPartition attributes. By default, hyperthreading is enabled when nPartitions are created to run HP-UX. The default attribute values are applied without a need for user intervention. The partition management software applies pre-determined OS specific defaults when you create a partition for a specific operating system type. However, there is also support for a new pardefault command, which displays the operating system specific attribute values and allows users to change them if needed: pardefault [Original Defaults] Parcon Default OS Type OS Type Hyper Threading at activation SLM Percentage ILM granule size SLM granule size VGA : HPUX_11iV3 : HPUX_11iV3 : Enabled : 87.50% : 1024 MB : 1024 MB : Enabled [Current Defaults] Parcon Default OS Type OS Type Hyper Threading at activation SLM Percentage : HPUX_11iV3 : HPUX_11iV3 : Enabled : 87.50% Operating system specific default values for nPartition attributes 25

Section	Page
HP Superdome 2 Partitioning Administrator Guide	1
Contents	3
1 Introduction	7
Overview	7
HP Superdome 2 terminology	8
2 Partitioning in HP Superdome 2	9
Onboard Administrator and Partition Management	9
Accessing the OA	9
OA CLI	9
OA GUI	9
Managing Partitions – basics	10
nPartitions	10
Virtual Partitions (vPars)	11
Commands: Partition Help pages	11
Commands: Partition commands logging	12
Log file location and log format	12
Cases where no logging occurs	12
Cases where logging occurs	13
Constraints and restrictions to logging	13
Ordering and licensing	13
nPartitions licensing	13
Virtual Partitions licensing	13
Related software licensing	14
Ordering vPars	14
nPartition and Virtual Partition unique identifiers	14
3 Getting started with nPartitions	17
Administration tool for nPartitions	17
Onboard Partition Manager	17
Commands for configuring nPartitions	17
nPartition resources	18
Assigned or unassigned blades and I/O bays	19
Active and inactive blades	20
I/O Enclosures and I/O bays	20
Finding the resource path of I/O	20
nPartition properties	20
Partition names	21
Partition numbers	21
Hyperthreading	21
Enabling or disabling Hyperthreading on HP Superdome 2 using the GUI	21
Enabling or disabling Hyperthreading on HP Superdome 2 using the CLI	21
Socket Local Memory	21
Blade resource attributes	22
Operating system specific default values for nPartition attributes	25
Partition State and RunStates	26
Partition specifications (parspec)	28
Creating a Partition specification	29
Creating an nPartition from a Partition specification	29
Removing a Partition specification	29
Saving the current configuration of nPartition and switch to an alternate configuration	29
Identifying Partition specification using the OA GUI	29
4 Planning nPartitions	31
Recommended HP Superdome 2 nPartition configurations	31
HP Superdome 2 Partitioning choices	31
Superdome 2 CPU / CPU module support	34
CPU mixing support	35
HP Superdome 2 memory support	35
Sample procedure for creating nPartitions	35
5 Creating and configuring nPartitions	38
Tools for configuring nPartitions	38
Commands to configure nPartitions	38
Granting permission for an OS to manage nPartitions	38
Task summaries for creating and configuring nPartitions	39
Partition default attributes	39
Creating a new nPartition	40
Creating a new nPartition using the OA CLI	40
Creating a new nPartition using the OA GUI	40
Verifying newly created nPartitions using the CLI	41
Verifying newly created nPartitions using the OA GUI	42
Removing an nPartition	42
Removing an nPartition using the OA CLI	42
Removing (Deleting) an nPartition using the OA GUI	43
Renaming an nPartition	43
Renaming an nPartition using the OA CLI	43
Renaming an nPartition using the OA GUI	43
Assigning blades and I/O bays to an nPartition	43
Assigning blades and I/O bays to an nPartition using the OA CLI	43
Assigning blades and I/O bays to an nPartition using the OA GUI	44
Removing blades and I/O bays from an nPartition	45
Removing blades and I/O bays from an nPartition using the OA CLI	45
Removing blades and I/O bays from an nPartition using the OA GUI	46
Renaming a server complex	47
Setting blade attributes	47
Setting blade attributes using the OA CLI	48
Setting blade attributes using the OA GUI	48
6 Booting and resetting Partitions (nPartitions and vPars)	50
Overview of Partition system booting	50
Booting to UEFI and preparing for Operating System installation	50
Booting from the CLI	51
Booting from the GUI	52
Getting a Console using the CLI	55
Getting a Console using the GUI	55
UEFI I/O device connection solution	56
Device Connection Policies	57
Confirming the Installed IO cards	58
Getting MAC Addresses for Ignite-UX	59
Task Summaries for Rebooting and Resetting Partitions	60
POWEROFF PARTITION	61
POWERON PARTITION	64
REBOOT PARTITION	64
SET PARTITION DVD	65
SHOW PARTITION DVD	67
SHOW PARTITION INFO	69
Force System Reset and Crash Dump (TOC) PARTITION	69
UPDATE NPARTITION	70
UPDATE SHOW NPARTITION	72
UPDATE FIRMWARE	72
UPDATE SHOW FIRMWARE	72
HP Superdome 2 Boot Support	73
Local Boot	74
Considerations for Local Boot	74
Boot from local SAN	74
Boot from External SAN	74
nPartition and Resource Health Status	75
Viewing Partition and Resource Health Status Using the CLI	75
Viewing Partition and Resource Health Status Using the OA GUI	77
Resource health policy	77
7 Planning Your System for Virtual Partitions	79
Planning Your Virtual Partitions	79
Virtual Partitions Layout Plan	79
Virtual Partition Names	79
Minimal Hardware Configuration	80
CPU-core	80
CPU-core: Boot Processor Definitions	80
CPU-core: Specifying Min and Max Limits	80
CPU-core: Adding and Deleting by Total	81
vparcreate	81
vparmodify	82
CPU-core: Adding or Deleting by Socket Local Processor (SLP)	82
CPU-core: Adding or Deleting by Resource Path	83
CPU: Summary Information	83
Deleting CPU-cores Summary	84
CPU Allocation	84
Memory	84
Assigning Memory to a vPar	85
I/O	85
Assigning I/O at the rootport or I/O slot Level	85
Syntax, Rules, and Notes	86
Counts Summary	87
Parspec change policy	87
A note on Deconfiguration	87
8 Managing and Booting Virtual Partitions	89
Modes: Switching between nPars and vPars Modes	89
Modes	89
Setting the mode using the OA GUI	89
Setting the mode using the OA CLI	91
Getting the vPar Console	92
Managing: Creating a Virtual Partition	93
Booting a Virtual Partition	93
Managing: Modifying Attributes of a Virtual Partition	94
Commands: Displaying vPars Resource Information (vparstatus)	95
Virtual Partition States	95
vparstatus: Summary Information	96
Shutting Down or Rebooting a Virtual Partition	98
Shutting Down All Virtual Partitions	99
Managing: Removing a Virtual Partition	99
Boot options management for partitions	100
9 Installing or Removing the vPars product from the OS	101
Before You Install the vPars Software	101
Installing vPars	101
Bundle Names	103
vPars Product Bundles	103
Ignite-UX Cookbook	103
Removing the vPars Product	103
10 Support and other resources	104
Contacting HP	104
Before you contact HP	104
HP contact information	104
Subscription service	104
Documentation feedback	104
Related information	104
Typographic conventions	105
A Partition commands	107
Glossary	108

Match case Limit results 1 per page

ILM granule size at next boot

: 1024 MB

SLM granule size

: 1024 MB

SLM granule size at next boot

: 1024 MB

Max number of ILM granules possible

: 1024

Max number of SLM granules possible

: 1024

User Specified Max number of blades

: 8

Max number of blades at next boot

: 8

User Specified Max number of vpars

: 16

Max number of vpars at next boot

: 16

Current boot mode

: npars

Next boot mode

: npars

Parspec Change Policy

: Enabled

VGA

: Enabled

VGA next boot mode

: Enabled

Pending Deletion

: -

parstatus -C

[Blade]

Enclosure/

Usage/

CPU

Memory (GB)

Use

Par

Pending

Blade

Status*

OK/

(GB)

Num

Deletion

Indicted/

OK/

Deconf

Indicted/

Boot

Max

Deconf

===

===================

=======

============= ====== ====== ==========

1/5

InActive Base/OK

8/0/0/8

16.0/0.0/0.0

yes

1/7

Inactive Base/OK

8/0/0/8

16.0/0.0/0.0

yes

D-Degraded

I-Indicted

NOTE:

On SD2, for an nPar in npar mode, nPars are created with a default ILM/SLM distribution

of 1:7 when no value is specified for SLM. For an nPar created in vpar mode, the default is to use

100% ILM.

Operating system specific default values for nPartition attributes

When an nPartition is created for a specific operating system type, the default values specific to

that operating system type are applied to the nPartition attributes. By default, hyperthreading is

enabled when nPartitions are created to run HP-UX. The default attribute values are applied without

a need for user intervention. The partition management software applies pre-determined OS specific

defaults when you create a partition for a specific operating system type. However, there is also

support for a new

pardefault

command, which displays the operating system specific attribute

values and allows users to change them if needed:

pardefault

[Original Defaults]

Parcon Default OS Type

: HPUX_11iV3

OS Type

: HPUX_11iV3

Hyper Threading at activation

: Enabled

SLM Percentage

: 87.50%

ILM granule size

: 1024 MB

SLM granule size

: 1024 MB

VGA

: Enabled

[Current Defaults]

Parcon Default OS Type

: HPUX_11iV3

OS Type

: HPUX_11iV3

Hyper Threading at activation

: Enabled

SLM Percentage

: 87.50%

Operating system specific default values for nPartition attributes