HP Integrity Superdome 2 16-socket HP Superdome 2 Partitioning Administrator G - Page 51

Booting from the CLI, parstatus -P

Get HP Integrity Superdome 2 16-socket PDF manuals and user guides View all HP Integrity Superdome 2 16-socket manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Booting from the CLI To activate a partition from the command line, you can either use the poweron partition {identifier} command, the bo command, or the pe command. poweron partition 2 Poweron request sent to partition 2. Operation initiated successfully. Please run PARSTATUS/VPARSTATUS or SHOW SYSLOG OA to determine the completion status of the operation. After you power on the nPartition, the partition firmware is booted and comes up to the Active/EFI state if the nPartition is in nPars mode or to Active/RUN_VPARS state if the nPartition is in vPars mode. parstatus -P [Partition] Par State/ Status* # of # of ILM/ Partition Name Num RunState Blades IOBays SLM (first 15 (GB)** characters) 1 Inactive /DOWN OK 1 0 0.0/0.0 nPar0001 2 Active /RUN_VPARS OK 2 2 2.0/28.0 nPar0002 3 Active /EFI OK 1 2 2.0/28.0 hard_partition 4 Inactive /DOWN OK 0 0 0.0/0.0 nPar0004 5 Inactive /DOWN OK 0 0 0.0/0.0 nPar0005 * D-Degraded ** Actual allocated for Active and User requested for Inactive partitions Booting to UEFI and preparing for Operating System installation 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Booting from the CLI
To activate a partition from the command line, you can either use the
poweron partition
{identifier}
command, the
bo
command, or the
pe
command.
poweron partition 2
Poweron request sent to partition 2. Operation initiated successfully.
Please run PARSTATUS/VPARSTATUS or SHOW SYSLOG OA to determine the completion
status of the operation.
After you power on the nPartition, the partition firmware is booted and comes up to the Active/EFI
state if the nPartition is in nPars mode or to Active/RUN_VPARS state if the nPartition is in vPars
mode.
parstatus -P
[Partition]
Par State/
Status* # of
# of
ILM/
Partition Name
Num RunState
Blades IOBays SLM
(first 15
(GB)**
characters)
=== ======================= ======= ====== ====== ============= ===============
1
Inactive /DOWN
OK
1
0
0.0/0.0
nPar0001
2
Active /RUN_VPARS
OK
2
2
2.0/28.0
nPar0002
3
Active /EFI
OK
1
2
2.0/28.0
hard_partition
4
Inactive /DOWN
OK
0
0
0.0/0.0
nPar0004
5
Inactive /DOWN
OK
0
0
0.0/0.0
nPar0005
*
D-Degraded
** Actual allocated for Active and User requested for Inactive partitions
Booting to UEFI and preparing for Operating System installation
51