HP J7934A HP Jetdirect 620n Print Server Setup Guide - Page 24

The HP Jetdirect 10/100Base-TX print server may, Troubleshooting Tools 24 - eio card

Get HP J7934A - JetDirect 620n Print Server PDF manuals and user guides
UPC - 829160279466
View all HP J7934A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Note The HP Jetdirect 10/100Base-TX print server may require up to 10 seconds to establish a connection on the network. Try the following troubleshooting procedures: ● Verify cabling connections. ● Configure the print server's 10/100TX link setting directly (for example, using the EIO menu on the printer's control panel). Verify that the configuration of the connecting network device (such as a network switch) matches. For example, if you set the print server for 100Base-TX Full-Duplex operation, the port on the network switch must also be set to 100Base-TX Full-Duplex operation. Power-cycle the printer to reinitialize the setting. ● On the Jetdirect Configuration Page, compare your configuration for the following parameters: Parameter PORT SELECT: PORT CONFIG: AUTONEGOTIATION: Expected Messages for 10/100TX Cards RJ-45 100TX HALF, 100TX FULL, 10BASE-T HALF, 10BASE-T FULL ON (Autonegotiation is enabled), or OFF (Autonegotiation is disabled, 10/100TX configuration has been manually set) For other configuration parameters and messages on the Jetdirect Configuration Page, refer to the applicable HP Jetdirect Administrator's Guide provided on the HP Jetdirect CD-ROM. ENWW Troubleshooting Tools 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Troubleshooting Tools 24
ENWW
Note
The HP Jetdirect 10/100Base-TX print server may
require up to
10 seconds
to establish a connection
on the network.
Try the following troubleshooting procedures:
●
Verify cabling connections.
●
Configure the print server’s 10/100TX link setting directly (for
example, using the EIO menu on the printer’s control panel).
Verify that the configuration of the connecting network device
(such as a network switch) matches. For example, if you set the
print server for 100Base-TX Full-Duplex operation, the port on
the network switch must also be set to 100Base-TX Full-Duplex
operation. Power-cycle the printer to reinitialize the setting.
●
On the Jetdirect Configuration Page, compare your configuration
for the following parameters:
For other configuration parameters and messages on the Jetdirect
Configuration Page, refer to the applicable
HP Jetdirect
Administrator’s Guide
provided on the HP Jetdirect CD-ROM.
Parameter
Expected Messages for 10/100TX Cards
PORT SELECT:
RJ-45
PORT CONFIG:
100TX HALF, 100TX FULL, 10BASE-T HALF,
10BASE-T FULL
AUTONEGOTIATION:
ON (Autonegotiation is enabled), or
OFF (Autonegotiation is disabled, 10/100TX
configuration has been manually set)