HP Pro Mini 400 G9 Desktop PC Maintenance and Service Guide - Page 35

Solid-state drive

Get HP Pro Mini 400 G9 Desktop PC PDF manuals and user guides View all HP Pro Mini 400 G9 Desktop PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2. Lift the connector latch on the system board, and then pull the tab (1) to disconnect the hard drive cable (2). 3. Remove the two Torx T15 screws (3) that secure the hard drive cage to the computer. 4. Slide the hard drive cage back, and then lift it out of the computer (4). To install the hard drive and cage, reverse the removal procedure. Solid-state drive To remove the solid-state drive module, use these procedures. The solid-state drive is located under the hard drive and drive cage. For list of available solid-state drives, see Computer major components on page 5. Before removing the solid-state drive module, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 20). 2. Remove the access panel (see Access panel on page 20). 28 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
2.
Lift the connector latch on the system board, and then pull the tab
(1)
to disconnect the hard drive cable
(2)
.
3.
Remove the two Torx T15 screws
(3)
that secure the hard drive cage to the computer.
4.
Slide the hard drive cage back, and then lift it out of the computer
(4)
.
To install the hard drive and cage, reverse the removal procedure.
Solid-state drive
To remove the solid-state drive module, use these procedures. The solid-state drive is located under the hard
drive and drive cage.
For list of available solid-state drives, see
Computer major components
on page
5
.
Before removing the solid-state drive module, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
20
).
2.
Remove the access panel (see
Access panel
on page
20
).
28
Chapter 4
Removal and replacement procedures