HP R/T2200 IEC-320-C14 HP Power Protector User Guide - Page 17

Setup overview, Browse to the HPPP Administrator or Client.

Get HP R/T2200 IEC-320-C14 PDF manuals and user guides View all HP R/T2200 IEC-320-C14 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Setup overview To setup HPPP: 1. Visit the HP website (http://www.hp.com/go/rackandpower) to download the latest version of HPPP. 2. Connect all equipment powered by the UPS to the receptacles on the UPS rear panel. If the UPS has multiple load segments, note which load segment powers each device. 3. Power up the UPS and all attached equipment. 4. Be sure that the serial or USB cable connecting the UPS to the HPPP is properly installed. 5. Install the HPPP Administrator or Client software according to the instructions for your operating system. If the configuration does not contain an HP UPS Network Module, there must be one HPPP Administrator for each UPS. 6. Browse to the HPPP Administrator or Client. 7. Configure the power source on the Device Discovery screen (on page 50) for both the HPPP Administrator and the Client. Be sure to configure the Administrator power source before configuring the Client. 8. Configure the power fail settings on the Shutdown Parameters screen (on page 59). 9. Test shutdown. 10. Configure event actions on the Event Actions screen (on page 54). 11. Configure user accounts on the User Accounts screen (on page 68). 12. Configure system settings on the System screen (on page 66). Overview 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
Overview 17
Setup overview
To setup HPPP:
1.
Visit the HP website (
) to download the latest version of HPPP.
2.
Connect all equipment powered by the UPS to the receptacles on the UPS rear panel. If the UPS has
multiple load segments, note which load segment powers each device.
3.
Power up the UPS and all attached equipment.
4.
Be sure that the serial or USB cable connecting the UPS to the HPPP is properly installed.
5.
Install the HPPP Administrator or Client software according to the instructions for your operating system.
If the configuration does not contain an HP UPS Network Module, there must be one HPPP Administrator
for each UPS.
6.
Browse to the HPPP Administrator or Client.
7.
Configure the power source on the Device Discovery screen (on page
50
) for both the HPPP
Administrator and the Client. Be sure to configure the Administrator power source before configuring
the Client.
8.
Configure the power fail settings on the Shutdown Parameters screen (on page
59
).
9.
Test shutdown.
10.
Configure event actions on the Event Actions screen (on page
54
).
11.
Configure user accounts on the User Accounts screen (on page
68
).
12.
Configure system settings on the System screen (on page
66
).