HP Scitex FB550 Site Preparation Guide - Page 8

Safety information

Get HP Scitex FB550 PDF manuals and user guides View all HP Scitex FB550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

● Final preparation and site cleaning prior to installation. ● Familiarity and compliance with all applicable local laws, regulations, and standards, including those regarding waste ink disposal and VOCs. Safety information ● UV light - The UV curing lamps emit high power UV light. The printer must be operated with all safety shielding installed to protect the operator from eye and skin damage. When operated according to manufacturer's instructions, safety glasses or other protective clothing are not necessary. ● Mechanical hazards - Keep fingers away from carriage and media path. Use a fork lift truck to lift the printer. Do not exceed the maximum weight load of the input or output tables, as printed on the label. ● Ink - Read and practice safety guidelines as outlined in the MSDS for the ink, and post the document in the work area as required by prevailing law. Avoid any contact with skin and eyes. None of the component substances have established exposure standards per OSHA, NIOSH or ACGIH. Collect waste ink in container provided. Dispose of ink according to MSDS and local regulations. Keep the waste-ink spigot closed during printing. ● Special ventilation is not required to meet US OSHA requirements on occupational exposure to VOCs from the HP UV-curable inks used with the printer. Special ventilation equipment installation is at the discretion of the customer; no specific HP recommendation is intended. Customers should consult state and local requirements and regulations. ● Electrical - WITH THE POWER SWITCH IN THE OFF POSITION, POWER MAY STILL BE SUPPLIED TO THE PRINTER COMPONENTS. To completely cut power from the printer, you must unplug the power cord from the power outlet. ● Ozone - The high power UV light emitted by the curing lamps reacts with oxygen and produces ozone. This formation tends to be greatest during lamp start-up. The lamps include ozone filters to reduce ozone production. The printer should be operated in a well-ventilated area to avoid minor effects such as headaches, fatigue, and dryness of the upper respiratory tract. Normal air movement will mix the ozone with fresh air, causing it to revert back to oxygen. ● Hazardous waste - THE PRINTER ELECTRONICS ASSEMBLY CONTAINS A LITHIUM BATTERY DEVICE. THERE IS A DANGER OF EXPLOSION IF THE BATTERY IS INCORRECTLY REPLACED. The battery must be replaced only by authorized service providers, and must be replaced only with the same or equivalent type. Dispose of this lithium battery device in accordance with local, state (or province), and Federal (or country) solid waste requirements. 2 Chapter 1 Introduction ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
●
Final preparation and site cleaning prior to installation.
●
Familiarity and compliance with all applicable local laws, regulations, and standards, including those
regarding waste ink disposal and VOCs.
Safety information
●
UV light
—
The UV curing lamps emit high power UV light. The printer must be operated with all safety
shielding installed to protect the operator from eye and skin damage. When operated according to
manufacturer’s instructions, safety glasses or other protective clothing are not necessary.
●
Mechanical hazards
—
Keep fingers away from carriage and media path. Use a fork lift truck to lift the
printer. Do not exceed the maximum weight load of the input or output tables, as printed on the label.
●
Ink
—
Read and practice safety guidelines as outlined in the MSDS for the ink, and post the document in
the work area as required by prevailing law. Avoid any contact with skin and eyes. None of the
component substances have established exposure standards per OSHA, NIOSH or ACGIH. Collect waste
ink in container provided. Dispose of ink according to MSDS and local regulations. Keep the waste-ink
spigot closed during printing.
●
Special ventilation is not required to meet US OSHA requirements on occupational exposure to VOCs
from the HP UV-curable inks used with the printer. Special ventilation equipment installation is at the
discretion of the customer; no specific HP recommendation is intended. Customers should consult state
and local requirements and regulations.
●
Electrical
—
WITH THE POWER SWITCH IN THE OFF POSITION, POWER MAY STILL BE SUPPLIED TO THE
PRINTER COMPONENTS. To completely cut power from the printer, you must unplug the power cord
from the power outlet.
●
Ozone
—
The high power UV light emitted by the curing lamps reacts with oxygen and produces ozone.
This formation tends to be greatest during lamp start-up. The lamps include ozone filters to reduce
ozone production. The printer should be operated in a well-ventilated area to avoid minor effects such
as headaches, fatigue, and dryness of the upper respiratory tract. Normal air movement will mix the
ozone with fresh air, causing it to revert back to oxygen.
●
Hazardous waste
—
THE PRINTER ELECTRONICS ASSEMBLY CONTAINS A LITHIUM BATTERY DEVICE.
THERE IS A DANGER OF EXPLOSION IF THE BATTERY IS INCORRECTLY REPLACED. The battery must be
replaced only by authorized service providers, and must be replaced only with the same or equivalent
type. Dispose of this lithium battery device in accordance with local, state (or province), and Federal (or
country) solid waste requirements.
2
Chapter 1
Introduction
ENWW