HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.1.0c release notes (5697-7680 - Page 17

HP StorageWorks Fabric OS 6.1.0c release notes

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Closed defect summary Solution On disabling the proxy switch (FOS 6.0 ), no event received on the SMIA agent side. Fixed in Fabric OS 6.1.0 When HA sync was stopped, a SAN Director 2/128 did not output the FW-1433 message. Fixed in Fabric OS 6.1.0 For ISL_RDY mode, transmit credit is exceeds its limit at 250. It works okay if required buffer is less than 250 (ie. 250km at 2G). Fixed in Fabric OS 6.1.0 Fastwrite with tape pipeline, switch sent improper frame caused tape job to fail. Fixed in Fabric OS 6.1.0 For Tapepipelining the FCP RSP does not come from Fabric. Fixed in Fabric OS 6.1.0 supportshow does not include portcfgvexport data for VEX_Ports. Fixed in Fabric OS 6.1.0 In some cases where an FCIP address is on a different subnet, a MAC level broadcast is sent instead of the router's MAC. Fixed in Fabric OS 6.1.0 Hot plug Core Blade with POST on, the blade comes up Faulty(51) due to turbo RAM test failure. Fixed in Fabric OS 6.1.0 Web Tools enable config option cannot configure the maximum supported number of zones (2047). Fixed in Fabric OS 6.1.0 Editing IPv6 prefix length from Web Tools does not work. Fixed in Fabric OS 6.1.0 cfgdisable fails on MP Router 400 running in XRC configuration. Fixed in Fabric OS 6.1.0 FIPS related changes required in response to a FIPS audit. Fixed in Fabric OS 6.1.0 SRDFA suspends in a fast-write environment. Fixed in Fabric OS 6.1.0 A device disappears after server reboot in a FICON environment. Fixed in Fabric OS 6.1.0 FC4-48 blade drops frame on the 4/256 SAN Director on ports that are routed through Director ports above 256. Fixed in Fabric OS 6.1.0 IBM FICON Qual. The FW message needs to specify the blade number when a port blade faults in the DC Director.. Fixed in Fabric OS 6.1.0 porttest not working. Fixed in Fabric OS 6.1.0 Need to add a delay to the PLOGI ACCept for all well known addresses. Fixed in Fabric OS 6.1.0 Operator-disabled ports are displayed as marginal under specific conditions. Fixed in Fabric OS 6.1.0 firmwaredownload pre-install script fails to detect that QOS links are active prior to a downgrade. Fixed in Fabric OS 6.1.0 Phantom power supply faults logged against the DC Director. Fixed in Fabric OS 6.1.0 Power supply status incorrectly identified as marginal when power supplies are in certain slots. Fixed in Fabric OS 6.1.0 The switch status is shown as Healthy with one core blade even when the policy is set to show as marginal on removal/failure of a core Fixed in Fabric OS 6.1.0 blade. FICON Tape Pipelining with specific tape devices results in block count mismatch errors. Fixed in Fabric OS 6.1.0 A DC Director might erroneously report a failed attempt at reading a temperature sensor as -1° Celsius. Fixed in Fabric OS 6.1.0 On an FR4-48 with FMS enabled, duplicate port names for some ports that share the same address. Fixed in Fabric OS 6.1.0 HP StorageWorks Fabric OS 6.1.0c release notes 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
Closed defect summary
Solution
On disabling the proxy switch (FOS 6.0 ), no event received on the
SMIA agent side.
Fixed in Fabric OS 6.1.0
When HA sync was stopped, a SAN Director 2/128 did not output
the FW-1433 message.
Fixed in Fabric OS 6.1.0
For ISL_RDY mode, transmit credit is exceeds its limit at 250. It works
okay if required buffer is less than 250 (ie. 250km at 2G).
Fixed in Fabric OS 6.1.0
Fastwrite
with tape pipeline, switch sent improper frame caused
tape job to fail.
Fixed in Fabric OS 6.1.0
For Tapepipelining the FCP RSP does not come from Fabric.
Fixed in Fabric OS 6.1.0
supportshow
does not include
portcfgvexport
data for
VEX_Ports.
Fixed in Fabric OS 6.1.0
In some cases where an FCIP address is on a different subnet, a MAC
level broadcast is sent instead of the router’s MAC.
Fixed in Fabric OS 6.1.0
Hot plug Core Blade with POST on, the blade comes up Faulty(51)
due to turbo RAM test failure.
Fixed in Fabric OS 6.1.0
Web Tools enable
config
option cannot con
fi
gure the maximum
supported number of zones (2047).
Fixed in Fabric OS 6.1.0
Editing IPv6 pre
fi
x length from Web Tools does not work.
Fixed in Fabric OS 6.1.0
cfgdisable
fails on MP Router 400 running in XRC con
fi
guration.
Fixed in Fabric OS 6.1.0
FIPS related changes required in response to a FIPS audit.
Fixed in Fabric OS 6.1.0
SRDFA suspends in a fast-write environment.
Fixed in Fabric OS 6.1.0
A device disappears after server reboot in a FICON environment.
Fixed in Fabric OS 6.1.0
FC4-48 blade drops frame on the 4/256 SAN Director on ports that
are routed through Director ports above 256.
Fixed in Fabric OS 6.1.0
IBM FICON Qual. The
FW
message needs to specify the blade
number when a port blade faults in the DC Director..
Fixed in Fabric OS 6.1.0
porttest
not working.
Fixed in Fabric OS 6.1.0
Need to add a delay to the PLOGI ACCept for all well known
addresses.
Fixed in Fabric OS 6.1.0
Operator-disabled ports are displayed as marginal under speci
fi
c
conditions.
Fixed in Fabric OS 6.1.0
firmwaredownload
pre-install script fails to detect that QOS links
are active prior to a downgrade.
Fixed in Fabric OS 6.1.0
Phantom power supply faults logged against the DC Director.
Fixed in Fabric OS 6.1.0
Power supply status incorrectly identi
fi
ed as marginal when power
supplies are in certain slots.
Fixed in Fabric OS 6.1.0
The switch status is shown as Healthy with one core blade even when
the policy is set to show as marginal on removal/failure of a core
blade.
Fixed in Fabric OS 6.1.0
FICON Tape Pipelining with speci
fi
c tape devices results in block
count mismatch errors.
Fixed in Fabric OS 6.1.0
A DC Director might erroneously report a failed attempt at reading a
temperature sensor as -1° Celsius.
Fixed in Fabric OS 6.1.0
On an FR4-48 with FMS enabled, duplicate port names for some
ports that share the same address.
Fixed in Fabric OS 6.1.0
HP StorageWorks Fabric OS 6.1.0c release notes
17