HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.1.2 release notes (5697-0349, - Page 14

DC SAN Director blade support, Power supply requirements for Director blades, Number of blades

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

DC SAN Director blade support Fabric OS 6.1.2 is fully qualified and supports the DC SAN Director blades listed in Table 4. Table 4 DC SAN Director blade support matrix Director blade FC8-16 FC8-32 FC8-48 FC10-6 Number of blades Supported with Fabric OS 6.0.0b and later with any mix and up to eight blades of each type. No intermix restrictions. FC4-16IP (iSCSI blade) Not supported with the DC SAN Director FR4-18i (FCIP/FC Router blade) Supported with Fabric OS 6.0.0b and later with a maximum of four blades of this type. Up to eight FR4-18i blades can be installed if they are used only for FC Fast Write or FCIP without routing. Power supply requirements for Director blades Table 5 lists power supply requirements for Director blades to provide full redundancy (220 VAC power is assumed). IMPORTANT: Director blades must meet minimum Fabric OS levels to operate in the Director chassis. For example, the FC8-32 is not supported in the 4/256 SAN Director with Fabric OS 6.0.x. Table 5 Power supplies required for blades in Director chassis Director blade FC4-16 FC4-32 FC4-48 FC8-16 FC8-32 4/256 SAN Director Two power supplies DC SAN Director1 Two power supplies FC8-48 FC10-6 Four power supplies Two power supplies FR4-18i (FCIP/FC Router blade) Four power supplies FC4-16IP (iSCSI blade) Two power supplies. FC4-16IP blades are not supported in the DC SAN Director. 1The DC Director can operate with nominal power of 110 VAC. See the appropriate hardware reference guide for power specifications. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
DC SAN Director blade support
Fabric OS 6.1.2 is fully qualified and supports the DC SAN Director blades listed in
Table 4
.
Table 4 DC SAN Director blade support matrix
Number of blades
Director blade
Supported with Fabric OS 6.0.0b and later with any mix
and up to eight blades of each type. No intermix
restrictions.
FC8-16
FC8-32
FC8-48
FC10-6
Not supported with the DC SAN Director
FC4-16IP (iSCSI blade)
Supported with Fabric OS 6.0.0b and later with a
maximum of four blades of this type. Up to eight FR4-18i
blades can be installed if they are used only for FC Fast
Write or FCIP without routing.
FR4-18i (FCIP/FC Router blade)
Power supply requirements for Director blades
Table 5
lists power supply requirements for Director blades to provide full redundancy (220 VAC
power is assumed).
IMPORTANT:
Director blades must meet minimum Fabric OS levels to operate in the Director chassis. For example,
the FC8-32 is not supported in the 4/256 SAN Director with Fabric OS 6.0.x.
Table 5 Power supplies required for blades in Director chassis
DC SAN Director
1
4/256 SAN Director
Director blade
Two power supplies
Two power supplies
FC4-16
FC4-32
FC4-48
FC8-16
FC8-32
Two power supplies
Four power supplies
FC8-48
FC10-6
Two power supplies. FC4-16IP blades are
not supported in the DC SAN Director.
Four power supplies
FR4-18i (FCIP/FC Router blade)
FC4-16IP (iSCSI blade)
1
The DC Director can operate with nominal power of 110 VAC. See the appropriate hardware reference guide for power
specifications.
14