HP Value Microportable Projector MP1400 Compaq MP1400 Microportable Projector - Page 32

Special On-Screen Messages, Check Video Cable, Input Signal Out of Range, Inputs Active - Remove One

Get HP Value Microportable Projector MP1400 PDF manuals and user guides View all HP Value Microportable Projector MP1400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

s Management-Allows the user to control power saver characteristics of the display, or to view the cumulative lamp hours, reset the lamp hour timer, view the unit's serial number, or perform a Master Reset. s Factory Reset-Resets the current operating option to its original factory setting. Special On-Screen Messages The following on-screen messages will appear on the projection display to identify the following conditions: s Check Video Cable-Indicates the video cable may not be plugged into the projector or the selected video input is not accurate. s Input Signal Out of Range-Indicates the projector is unable to access the appropriate input signal. s 2 Inputs Active - Remove One-The projector has two data inputs: one is an analog D-Sub input, and the other is a digital DFP input. This message indicates that both inputs are active simultaneously and the user should detach one of them. s Going to Standby-Indicates the projector is entering a sleep mode or is powering off the lamp. s Lamp May Fail Soon, Replacement Suggested-Indicates the lamp is approaching failure. The message will remain on the screen for five seconds or until the on-screen menu Select button is pressed.  MP1400 Microportable Projector  2-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
MP1400 Microportable Projector
2-7
■
Management—Allows the user to control power saver
characteristics of the display, or to view the cumulative lamp
hours, reset the lamp hour timer, view the unit’s serial number,
or perform a Master Reset.
■
Factory Reset—Resets the current operating option to its
original factory setting.
Special On-Screen Messages
The following on-screen messages will appear on the projection
display to identify the following conditions:
■
Check Video Cable—
Indicates the video cable may not be
plugged into the projector or the selected video input is not
accurate.
■
Input Signal Out of Range—
Indicates the projector is unable
to access the appropriate input signal.
■
2 Inputs Active - Remove One—
The projector has two data
inputs: one is an analog D-Sub input, and the other is a digital
DFP input. This message indicates that both inputs are active
simultaneously and the user should detach one of them.
■
Going to Standby—
Indicates the projector is entering a sleep
mode or is powering off the lamp.
■
Lamp May Fail Soon, Replacement Suggested—
Indicates
the lamp is approaching failure. The message will remain on
the screen for five seconds or until the on-screen menu
Select
button is pressed.