HP Value Microportable Projector MP1400 Compaq MP1400 Microportable Projector - Page 59

Solving Lamp Problems

Get HP Value Microportable Projector MP1400 PDF manuals and user guides View all HP Value Microportable Projector MP1400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Solving Lamp Problems Lamp shuts off 1. If all five projector panel buttons flash amber, the projector has overheated and will automatically shut down. Wait 5-10 minutes until the buttons stop flashing and the Standby button turns amber before restarting the projector again. 2. A minor power surge may cause the lamp to shut off. Turn the projector off. Wait a few minutes, then turn it back on. Lamp burns out or makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. For information on purchasing a replacement lamp module, call your Compaq authorized dealer, seller, or reseller. To locate a reseller near you, call 1-800-AT-COMPAQ. To purchase directly from Compaq, visit the Compaq web site at http://www.compaq.com/products/ projectors. To replace the lamp, follow the procedures in the "Replacing the Projector Lamp Module" section in Chapter 5, "Care and Maintenance."   Troubleshooting A-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Troubleshooting
A-5
Solving Lamp Problems
Lamp shuts off
1. If all five projector panel buttons
flash amber, the projector has
overheated and will automatically
shut down. Wait 5-10 minutes
until the buttons stop flashing
and the
Standby
button turns
amber before restarting the
projector again.
2. A minor power surge may cause
the lamp to shut off. Turn the
projector off. Wait a few minutes,
then turn it back on.
Lamp burns out or makes a
popping sound
When the lamp reaches its end of life,
it will burn out and may make a loud
popping sound. If this happens, the
projector will not turn back on until
the lamp module has been replaced.
For information on purchasing a
replacement lamp module, call your
Compaq authorized dealer, seller, or
reseller. To locate a reseller near you,
call 1-800-AT-COMPAQ. To purchase
directly from Compaq, visit the
Compaq web site at
projectors
.
To replace the lamp, follow the
procedures in the
“
Replacing the
Projector Lamp Module
”
section in
Chapter 5,
“
Care and Maintenance
.”