HP Xw6200 Adaptec SCSI RAID 2120S: Installation Guide - Page 46

Installing the Driver in an Existing NetWare5.1 or 6 Server, Storage, adapters, Modify

Get HP Xw6200 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 882780333536
View all HP Xw6200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing the Driver 4 Begin installing NetWare 5.1 on your server as instructed in your NetWare documentation. Make sure that you have the aacraid.ham and aacraid.ddi files available on the driver disk created at the beginning of this chapter. 5 When the Device Types screen appears, check the Storage adapters list and select Modify to add another driver. 6 Select the Storage adapters and press Enter. A list of recognized controllers will be displayed. If AACRAID was detected, delete it. 7 Press the Insert key to add another driver. The list of available drivers will be displayed on this screen. 8 Press the Enter key to scan drive A for the driver. You have a choice to press F3 and specify the path to the driver if it does not reside on drive A. 9 Once the driver is selected, the installation process returns to the parameter screen. 10 Verify the list of the loaded drivers and from the lower window menu, select Continue and press Enter. Note: If the driver installation process does not complete successfully you will be taken back to the server console to examine the cause of the failure. Installing the Driver in an Existing NetWare 5.1 or 6 Server In this scenario, you are integrating an Adaptec SCSI RAID controller into an existing Novell NetWare 5.1 or 6 server as a secondary controller. To install the driver: 1 Upgrade your NetWare server to the minimum patch level specified by Novell. 2 Make a backup copy of the driver. 3 Shutdown the server. 4 Install and configure the Adaptec SCSI RAID controller as a secondary controller according to the instructions in Chapter 2. 3-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
3-15
Installing the Driver
4
Begin installing NetWare 5.1 on your server as instructed in
your NetWare documentation. Make sure that you have the
aacraid.ham
and
aacraid.ddi
files available on the driver disk
created at the beginning of this chapter.
5
When the Device Types screen appears, check the
Storage
adapters
list and select
Modify
to add another driver.
6
Select the
Storage adapters
and press
Enter
. A list of recognized
controllers will be displayed. If AACRAID was detected, delete
it.
7
Press the
Insert
key to add another driver. The list of available
drivers will be displayed on this screen.
8
Press the
Enter
key to scan drive A for the driver. You have a
choice to press
F3
and specify the path to the driver if it does not
reside on drive A.
9
Once the driver is selected, the installation process returns to
the parameter screen.
10
Verify the list of the loaded drivers and from the lower window
menu, select
Continue
and press
Enter
.
Note:
If the driver installation process does not complete
successfully you will be taken back to the server console to
examine the cause of the failure.
Installing the Driver in an Existing NetWare 5.1 or 6 Server
In this scenario, you are integrating an Adaptec SCSI RAID
controller into an existing Novell NetWare 5.1 or 6 server as a
secondary controller.
To install the driver:
1
Upgrade your NetWare server to the minimum patch level
specified by Novell.
2
Make a backup copy of the driver.
3
Shutdown the server.
4
Install and configure the Adaptec SCSI RAID controller as a
secondary controller according to the instructions in
Chapter 2
.