Husqvarna AUTOMOWER 220 AC Owners Manual - Page 29

while result in a broken circuit., Laying the boundary wire in towards the charging

Get Husqvarna AUTOMOWER 220 AC PDF manuals and user guides View all Husqvarna AUTOMOWER 220 AC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

3. INSTALLATION The boundary wire must not be crossed on the path to and from an island. Laying the boundary wire in towards the charging station The boundary wire can be routed in several different 1. ways in towards the charging station. The best alternative is to route the wire completely outside the charging station, see alternative 1. The wire can also be placed under the charging station plate as shown 2. in alternative 2 in the illustration. However, the wire should not be placed outside alternative 2 because it can then be difficult for Automower to find the charging station. When connecting to the charging station, the right end of the boundary wire should be guided into the right-hand hole and the cable's left end in the left-hand hole. Joining the boundary wire If the boundary wire is not long enough and needs to be spliced: Use original solderless coupler. It is waterproof and gives a reliable electrical connection. To splice: Insert both cable ends in the coupler. Now press down the button on top of the connector fully. Use a pair of pliers or the like, as the button on the connector is difficult to press down by hand. IMPORTANT INFORMATION Twisted cables, or a screw terminal (chock-block), insulated with insulation tape is not a satisfactory splice. Soil moisture will cause the conductors to oxidize and after a while result in a broken circuit. 30 - English 3012-686US 3012-671 3012-462 3012-832

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
30 - English
3. INSTALLATION
The boundary wire must not be crossed on the path
to and from an island.
Laying the boundary wire in towards the charging
station
The boundary wire can be routed in several different
ways in towards the charging station. The best
alternative is to route the wire completely outside the
charging station, see alternative 1. The wire can also
be placed under the charging station plate as shown
in alternative 2 in the illustration. However, the wire
should not be placed outside alternative 2 because it
can then be difficult for Automower to find the
charging station.
When connecting to the charging station, the right
end of the boundary wire should be guided into the
right-hand hole and the cable's left end in the
left-hand hole.
Joining the boundary wire
If the boundary wire is not long enough and needs to
be spliced: Use original solderless coupler. It is
waterproof and gives a reliable electrical connection.
To splice: Insert both cable ends in the coupler. Now
press down the button on top of the connector fully.
Use a pair of pliers or the like, as the button on the
connector is difficult to press down by hand.
IMPORTANT INFORMATION
Twisted cables, or a screw terminal
(chock-block), insulated with insulation tape
is not a satisfactory splice. Soil moisture will
cause the conductors to oxidize and after a
while result in a broken circuit.
3012-686US
3012-671
1.
2.
3012-462
3012-832