Husqvarna RZ4824F Owners Manual - Page 34

Moving Machine By Hand, Use extreme caution when loading

Get Husqvarna RZ4824F PDF manuals and user guides View all Husqvarna RZ4824F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

OPERATION Moving Machine By Hand When pushing or pulling the mower, engage the EZT bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard. 1. Raise the deck into the highest cutting position. 2. Engage the parking brake. 3. Pull the EZT bypass linkages up and out of the keyhole slots. Release the levers with the head outside the frame and held in the bypass position. 4. To reengage the EZT's to drive, reverse the above procedure. Load the machine into truck or trailer by driving slowly up the ramps. DO NOT LIFT! The machine is not intended to be lifted by hand. Left side bypass linkage, EZT engaged WARNING! Bypass linkages are located close to the muffler. To prevent burns, the engine should be shut off and allowed to cool before the bypass linkage levers are handled. 8058-032 WARNING! Make no adjustments without: • the engine stopped, • the ignition key removed, • the parking brake activated 8058-033 Left side bypass linkage, EZT locked in the bypass position WARNING! Use extreme caution when loading the machine into a truck or trailer using ramps. There is the possibility of serious injury or death if the machine falls off the ramps. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
34
OPERATION
Moving Machine By Hand
When pushing or pulling the mower, engage the
EZT bypass linkages. The EZT bypass linkages are
located on the rear of the frame, below the rear engine
guard.
1.
Raise the deck into the highest cutting
position.
2.
Engage the parking brake.
3.
Pull the EZT bypass linkages up and out of
the keyhole slots. Release the levers with the
head outside the frame and held in the bypass
position.
4.
To reengage the EZT’s to drive, reverse the
above procedure.
Load the machine into truck or trailer by driving slowly
up the ramps. DO NOT LIFT! The machine is not
intended to be lifted by hand.
8058-032
Left side bypass linkage, EZT engaged
8058-033
Left side bypass linkage, EZT locked in the bypass position
WARNING!
Make no adjustments without:
•
the engine stopped,
•
the ignition key removed,
•
the parking brake activated
WARNING!
Use extreme caution when loading
the machine into a truck or trailer
using ramps. There is the possibility
of serious injury or death if the
machine falls off the ramps.
WARNING!
Bypass linkages are located close
to the muffler. To prevent burns, the
engine should be shut off and allowed
to cool before the bypass linkage
levers are handled.