Husqvarna RZ4824F Owners Manual - Page 40

V-belts, Deck Belt Removal, Deck Belt Installation - mandrel pulley

Get Husqvarna RZ4824F PDF manuals and user guides View all Husqvarna RZ4824F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

MAINTENANCE V-belts Check every 100 hours of operation. Check for severe cracking and large nicks. NOTE: The belt will show some small cracks in normal operation. The belts are not adjustable. Replace belts if they begin to slip from wear. Deck Belt Removal 1. Park on a level surface. Apply parking brake. 2. Lower the deck into the lowest cutting position. 3. Remove bolts from belt shields and remove shields. 4. Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface. 5. Remove tension on the belt by moving the idler arm. 6. Carefully slip belt up over the top of the cutter housing pulleys and remove belt. Rolling belt over the pulleys may damage the belt. Remove belt shields Deck Belt Installation NOTE: For ease in installing the deck belt, refer to 1 the routing decal on the top of the deck. 1. Wrap the deck belt around the electric clutch pulley that is located on the engine shaft. 2. Route the belt forward and up onto the deck. 3. Place belt around spring loaded idler pulley. 2 4. Wrap the belt around the stationary idler pulley and around the mandrel housings. 5. Push inward on the idler arm and carefully route belt over stationary idler pulley. Once belt is properly routed, slowly release idler arm to tension belt. 6. Double check belt routing to make sure it matches the routing decal, and the belt does not have any twist. Correct as needed. 7. Replace belt shields on both mandrel housings and secure with fasteners. 1. Clutch pulley position 2. Deck belt Belt routing, deck belt 8058-131 8061-034 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
40
MAINTENANCE
1
2
V-belts
Check every 100 hours of operation. Check for severe
cracking and large nicks.
NOTE: The belt will show some small cracks in normal
operation.
The belts are not adjustable. Replace belts if they
begin to slip from wear.
Deck Belt Removal
1.
Park on a level surface. Apply parking brake.
2.
Lower the deck into the lowest cutting position.
3.
Remove bolts from belt shields and remove
shields.
4.
Remove any dirt or grass that may have
accumulated around the cutter housings and
entire deck surface.
5.
Remove tension on the belt by moving the idler
arm.
6.
Carefully slip belt up over the top of the cutter
housing pulleys and remove belt. Rolling belt over
the pulleys may damage the belt.
8058-131
Remove belt shields
8061-034
1. Clutch pulley position
2. Deck belt
Belt routing, deck belt
Deck Belt Installation
NOTE: For ease in installing the deck belt, refer to
the routing decal on the top of the deck.
1.
Wrap the deck belt around the electric clutch
pulley that is located on the engine shaft.
2.
Route the belt forward and up onto the deck.
3.
Place belt around spring loaded idler pulley.
4.
Wrap the belt around the stationary idler pulley
and around the mandrel housings.
5.
Push inward on the idler arm and carefully route
belt over stationary idler pulley. Once belt is
properly routed, slowly release idler arm to tension
belt.
6.
Double check belt routing to make sure it matches
the routing decal, and the belt does not have any
twist. Correct as needed.
7.
Replace belt shields on both mandrel housings
and secure with fasteners.