Husqvarna RZ4824F Owners Manual - Page 41

Adjusting the Mower Deck, Leveling deck - belt

Get Husqvarna RZ4824F PDF manuals and user guides View all Husqvarna RZ4824F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

MAINTENANCE Adjusting the Mower Deck Leveling deck Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure. See "Technical Data" under Transmission. If tires are under or over inflated, the deck cannot be properly adjusted. The deck should be adjusted slightly higher in the rear. NOTE: To insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck. 1. Wear heavy gloves. Turn each outer blade tip to align with the deck or in a side-to-side manner. 2. Measure from the floor surface up to the bottom of the blade tip on the discharge side of the mower deck. Retain this measurement. 3. Move to the opposite side, check that measurement is the same. If adjustment is required-with a ¾" or adjustable wrench, turn the lift link adjustment nuts on either side counter clockwise to lower or clockwise to raise. Adjust until both side-to-side measurements are equal. Lift link adjustment nut 4. Turn any blade to align with the deck in frontto-rear manner. If the front blade tip does not measure 1/8" to ½" higher in the rear, follow the front adjustment instructions that follow. 5. With a 5/8 or adjustable wrench, turn the nuts on the front suspension linkage. Clockwise raises the front of the mower, counterclockwise will lower the front. Adjust nuts until rear of mower deck is positioned level to 1/8" higher in the rear than the side-to-side measurement. NOTE: This will place the mower deck in a base measurement position. Additional adjustment may be required to achieve desired cut for the type of grass or conditions being mowed. Deck front adjustment nuts 8058-030 8058-031 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
41
mAINTENANCE
Adjusting the Mower Deck
Leveling deck
Adjust the deck while the Mower is on a level
surFace. make sure the tires are inflated to the correct
pressure. See “Technical Data” under TransMission.
IF tires are under or over inflated, the deck cannot be
properlY adjusted.
The deck should be adjusted slightlY higher in the
rear.
NOTE: To insure accuracY oF leveling procedure,
Mower deck drive belt Must be installed prior to
leveling deck.
Wear heavY gloves. Turn each outer blade tip to
1.
align with the deck or in a side-to-side Manner.
measure FroM the floor surFace up to the bottoM oF
2.
the blade tip on the discharge side oF the Mower
deck. Retain this MeasureMent.
move to the opposite side, check that
3.
MeasureMent is the saMe. IF adjustMent is
required—with a ¾" or adjustable wrench, turn
the liFt link adjustMent nuts on either side counter
clockwise to lower or clockwise to raise. Adjust
until both side-to-side MeasureMents are equal.
8058-030
Lift link adjustment nut
8058-031
Deck front adjustment nuts
Turn anY blade to align with the deck in Front-
4.
to-rear Manner. IF the Front blade tip does not
Measure
1
/
8
" to ½" higher in the rear, Follow the
Front adjustMent instructions that Follow.
With a
5.
5
/
8
or adjustable wrench, turn the nuts on
the Front suspension linkage. Clockwise raises the
Front oF the Mower, counterclockwise will lower
the Front. Adjust nuts until rear oF Mower deck is
positioned level to
1
/
8
" higher in the rear than the
side-to-side MeasureMent.
NOTE: This will place the Mower deck in a base
MeasureMent position. Additional adjustMent MaY
be required to achieve desired cut For the tYpe oF
grass or conditions being Mowed.