IBM 3580-L23 Setup Guide - Page 27

Power-off the 3580 Ultrium 2 Tape Drive., single-character display.

Get IBM 3580-L23 PDF manuals and user guides View all IBM 3580-L23 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Note: If you inserted an invalid or write-protected tape cartridge, 7 appears in the single-character display. The 3580 Ultrium 2 Tape Drive unloads the cartridge and exits maintenance mode. v If no error is detected, the test will loop and begin again. To stop the loop, press and hold the unload button for several seconds. When the loop ends, 0 temporarily appears in the single-character display. The drive rewinds and unloads the tape, partially ejects the cartridge, then exits maintenance mode. The solid amber status light turns off and the following message displays: Passed! Tape Unloading followed by: Cartridge Unloading In Progress then: Ultrium Tape Drive Drive Empty v If an error is detected, the status light flashes amber, a message similar to the following displays, and the tape drive posts an error code to the single-character display. ERROR! Drive/Media Error To determine the error, locate the code in Table 8 on page 55. The tape drive unloads the tape cartridge, exits maintenance mode, and displays the following message: Ultrium Tape Drive Drive Empty Note: To reset the drive after an error occurs, cycle power (turn it off, then on again). __ 7. Power-off the 3580 Ultrium 2 Tape Drive. Chapter 2. Installing 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
Note:
If you inserted an invalid or write-protected tape cartridge,
7
appears
in the single-character display. The 3580 Ultrium 2 Tape Drive
unloads the cartridge and exits maintenance mode.
v
If no error is detected, the test will loop and begin again. To stop the
loop, press and hold the unload button for several seconds. When the
loop ends,
0
temporarily appears in the single-character display. The drive
rewinds and unloads the tape, partially ejects the cartridge, then exits
maintenance mode. The solid amber status light turns off and the
following message displays:
Passed!
Tape Unloading
followed by:
Cartridge Unloading
In Progress
then:
Ultrium Tape Drive
Drive Empty
v
If an error is detected, the status light flashes amber, a message similar to
the following displays, and the tape drive posts an error code to the
single-character display.
ERROR!
Drive/Media Error
To determine the error, locate the code in Table 8 on page 55. The tape
drive unloads the tape cartridge, exits maintenance mode, and displays
the following message:
Ultrium Tape Drive
Drive Empty
Note:
To reset the drive after an error occurs, cycle power (turn it off,
then on again).
__ 7.
Power-off the 3580 Ultrium 2 Tape Drive.
Chapter 2. Installing
11