IBM 3580-L23 Setup Guide - Page 56

Attention, Close the pivot arm

Get IBM 3580-L23 PDF manuals and user guides View all IBM 3580-L23 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

7. Position the tape in the alignment groove of the leader pin attach tool (see 1 in Figure 20). 8. Place a new C-clip into the retention groove 2 (Figure 20) on the leader pin attachment tool and make sure that the clip's open side faces up. 9. Place the leader pin (from step 6 on page 39) into the cavity 3 (Figure 20) of the leader pin attach tool. Attention: To prevent the leader pin from rolling into the cartridge, in the following step use care when folding the tape over the pin. 10. Fold the tape over the leader pin and hold it with your fingers (see Figure 20). Note: Use care to ensure that the tape is centered over the leader pin. Failure to properly center the tape on the pin will cause the repaired cartridge to fail. When the tape is properly centered, a 0.25-mm (0.01-in.) gap exists on both sides of the pin. 2 1 4 3 A67E0037 6 5 Figure 20. Attaching the leader pin to the tape 11. Close the pivot arm 4 of the leader pin attach tool by swinging it over the leader pin so that the C-clip snaps onto the pin and the tape. 12. Swing the pivot arm open and trim the excess tape 5 so that it is flush with the reattached leader pin 6 . 40 IBM 3580 Ultrium Tape Drive Setup and Operator Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
7.
Position the tape in the alignment groove of the leader pin attach tool (see
±1²
in Figure 20).
8.
Place a new C-clip into the retention groove
±2²
(Figure 20) on the leader pin
attachment tool and make sure that the clip
’
s open side faces up.
9.
Place the leader pin (from step 6 on page 39) into the cavity
±3²
(Figure 20) of
the leader pin attach tool.
Attention:
To prevent the leader pin from rolling into the cartridge, in the
following step use care when folding the tape over the pin.
10.
Fold the tape over the leader pin and hold it with your fingers (see Figure 20).
Note:
Use care to ensure that the tape is centered over the leader pin. Failure
to properly center the tape on the pin will cause the repaired cartridge
to fail. When the tape is properly centered, a 0.25-mm (0.01-in.) gap
exists on both sides of the pin.
11.
Close the pivot arm
±4²
of the leader pin attach tool by swinging it over the
leader pin so that the C-clip snaps onto the pin and the tape.
12.
Swing the pivot arm open and trim the excess tape
±5²
so that it is flush with
the reattached leader pin
±6²
.
A67E0037
1
6
2
3
4
5
Figure 20. Attaching the leader pin to the tape
40
IBM 3580 Ultrium Tape Drive Setup and Operator Guide