Intel BLKDQ35JOE Product Specification - Page 23

Real-Time Clock Subsystem, Legacy I/O Controller

Get Intel BLKDQ35JOE - 1333FSB DDR2 800 Audio Lan Raid SATA uATX 10Pack Motherboard PDF manuals and user guides
UPC - 200001401862
View all Intel BLKDQ35JOE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Product Description 1.8 Real-Time Clock Subsystem A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied. NOTE If the battery and AC power fail, custom defaults, if previously saved, will be loaded into CMOS RAM at power-on. When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS RAM (for example, the date and time) might not be accurate. Replace the battery with an equivalent one. Figure 1 on page 12 shows the location of the battery. 1.9 Legacy I/O Controller The I/O controller provides the following features: • One serial port header • Serial IRQ interface compatible with serialized IRQ support for PCI systems • Intelligent power management, including a programmable wake-up event interface • PCI power management support The BIOS Setup program provides configuration options for the I/O controller. 1.9.1 Serial Port The board has one serial port header located on the component side of the board. The serial port supports data transfers at speeds up to 115.2 kbits/sec with BIOS support. For information about The location of the serial port header The signal names of the serial port header Refer to Figure 11, page 45 Table 16, page 47 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Product Description
23
1.8
Real-Time Clock Subsystem
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory.
When
the computer is not plugged into a wall socket, the battery has an estimated life of
three years.
When the computer is plugged in, the standby current from the power
supply extends the life of the battery.
The clock is accurate to
±
13 minutes/year at
25 ºC with 3.3 VSB applied.
±
NOTE
If the battery and AC power fail, custom defaults, if previously saved, will be loaded
into CMOS RAM at power-on.
When the voltage drops below a certain level, the BIOS Setup program settings stored
in CMOS RAM (for example, the date and time) might not be accurate.
Replace the
battery with an equivalent one.
Figure 1 on page 12 shows the location of the battery.
1.9
Legacy I/O Controller
The I/O controller provides the following features:
•
One serial port header
•
Serial IRQ interface compatible with serialized IRQ support for PCI systems
•
Intelligent power management, including a programmable wake-up event interface
•
PCI power management support
The BIOS Setup program provides configuration options for the I/O controller.
1.9.1
Serial Port
The board has one serial port header located on the component side of the board.
The
serial port supports data transfers at speeds up to 115.2 kbits/sec with BIOS support.
For information about
Refer to
The location of the serial port header
Figure 11, page 45
The signal names of the serial port header
Table 16, page 47