Intel S5500BCR Service Guide - Page 37

Installing or Replacing the Processor

Get Intel S5500BCR PDF manuals and user guides View all Intel S5500BCR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Hardware Installations and Upgrades 5. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position (Step "A" in Figure 12). 6. Holding the DIMM by the edges, remove it from its anti-static package. 7. Position the DIMM above the socket. Align the small notch in the bottom edge of the DIMM with the key in the socket (Step "B" in Figure 12). 8. Insert the bottom edge of the DIMM into the socket (Step "C" in Figure 12). 9. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place (Step "D" in Figure 12). 10. Visually check that each latch is fully closed and correctly engaged with each DIMM edge slot (Step "E" in Figure 12). 11. Replace the server's cover and reconnect the AC power cord. Removing DIMMs To remove a DIMM, follow these steps: 1. Observe the safety and ESD precautions at the beginning of this book. For more information, see "Safety Information". 2. Turn off all peripheral devices connected to the server, and turn off the server. 3. Remove the AC power cord from the server. 4. Remove the server's cover. 5. Gently spread the retaining clips at each end of the socket. The DIMM lifts from the socket. 6. Holding the DIMM by the edges, lift it from the socket, and store it in an anti-static package. 7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets. 8. Replace the server's cover and reconnect the AC power cord. Installing or Replacing the Processor / NOTE Use the following instructions to install or replace a processor instead of using the instructions that came with the processor. CAUTION Processor must be appropriate: If you install a processor that is inappropriate for your server, you may damage the server board. See "Additional Information and Software" for a link to the list of compatible processor(s). ESD and handling processors: Reduce the risk of electrostatic discharge (ESD) damage to the processor by doing the following: (1) Touch the metal chassis before touching the processor or server board. Keep a part of your body in contact with the metal chassis to dissipate the static charge while handling the processor. (2) Avoid moving around unnecessarily. Installing the Processor To install a processor, follow these instructions: Intel® Server Board S5520HC, S5520HCT, and S5500HCV Service Guide 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Hardware Installations and Upgrades
Intel
®
Server Board S5520HC, S5520HCT, and S5500HCV Service Guide
25
5.
Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position (Step “A”
in Figure 12).
6.
Holding the DIMM by the edges, remove it from its anti-static package.
7.
Position the DIMM above the socket. Align the small notch in the bottom edge of the DIMM with the key in
the socket (Step “B” in Figure 12).
8.
Insert the bottom edge of the DIMM into the socket (Step “C” in Figure 12).
9.
When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into
place (Step “D” in Figure 12).
10. Visually check that each latch is fully closed and correctly engaged with each DIMM edge slot (Step “E” in
Figure 12).
11. Replace the server’s cover and reconnect the AC power cord.
Removing DIMMs
To remove a DIMM, follow these steps:
1.
Observe the safety and ESD precautions at the beginning of this book. For more information, see
“Safety
Information”
.
2.
Turn off all peripheral devices connected to the server, and turn off the server.
3.
Remove the AC power cord from the server.
4.
Remove the server’s cover.
5.
Gently spread the retaining clips at each end of the socket. The DIMM lifts from the socket.
6.
Holding the DIMM by the edges, lift it from the socket, and store it in an anti-static package.
7.
Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets.
8.
Replace the server’s cover and reconnect the AC power cord.
Installing or Replacing the Processor
/
NOTE
Use the following instructions to install or replace a processor instead of using the
instructions that came with the processor.
CAUTION
Processor must be appropriate:
If you install a processor that is
inappropriate for your server, you may damage the server board. See
“Additional
Information and Software”
for a link to the list of compatible processor(s).
ESD and handling processors:
Reduce the risk of electrostatic discharge
(ESD) damage to the processor by doing the following: (1) Touch the metal chassis
before touching the processor or server board. Keep a part of your body in contact
with the metal chassis to dissipate the static charge while handling the processor.
(2) Avoid moving around unnecessarily.
Installing the Processor
To install a processor, follow these instructions: