Intel S815EBM1 Product Guide - Page 21

Removing DIMMs, DIMM Socket Locations

Get Intel S815EBM1 - Server Board Motherboard PDF manuals and user guides
UPC - 735858149839
View all Intel S815EBM1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3. Remove the server's cover and locate the DIMM sockets (see Figure 4). 0 1 2 OM12202 Figure 4. DIMM Socket Locations 4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. 5. Holding the DIMM by the edges, remove it from its anti-static package. 6. Position the DIMM above the socket. Align the two small notches in the bottom edge of the DIMM with the keys in the socket (see inset in Figure 4). 7. Insert the bottom edge of the DIMM into the socket. 8. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 9. Replace the server's cover and reconnect the AC power cord. Removing DIMMs To remove a DIMM, follow these steps: 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Turn off all peripheral devices connected to the server. Turn off the server. 3. Remove the AC power cord from the server. 4. Remove the server's cover. 5. Gently spread the retaining clips at each end of the socket. The DIMM pops out of the socket. 6. Hold the DIMM by the edges, lift it away from the socket, and store it in an anti-static package. 7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets. 8. Replace the server's cover and reconnect the AC power cord. Upgrading 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Upgrading
21
3.
Remove the server
’
s cover and locate the DIMM sockets (see Figure 4).
OM12202
0
1
2
Figure 4.
DIMM Socket Locations
4.
Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open
position.
5.
Holding the DIMM by the edges, remove it from its anti-static package.
6.
Position the DIMM above the socket.
Align the two small notches in the bottom edge of the
DIMM with the keys in the socket (see inset in Figure 4).
7.
Insert the bottom edge of the DIMM into the socket.
8.
When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips
snap into place.
Make sure the clips are firmly in place.
9. Replace the server
’
s cover and reconnect the AC power cord.
Removing DIMMs
To remove a DIMM, follow these steps:
1.
Observe the safety and ESD precautions at the beginning of this chapter.
2.
Turn off all peripheral devices connected to the server.
Turn off the server.
3.
Remove the AC power cord from the server.
4. Remove the server
’
s cover.
5.
Gently spread the retaining clips at each end of the socket.
The DIMM pops out of the socket.
6.
Hold the DIMM by the edges, lift it away from the socket, and store it in an anti-static
package.
7.
Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets.
8. Replace the server
’
s cover and reconnect the AC power cord.