Intel SBXL52 Hardware Maintenance Manual - Page 102

Start the Configuration/Setup Utility program.

Get Intel SBXL52 - Server Compute Blade PDF manuals and user guides View all Intel SBXL52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

✏ NOTE See "System" on page 104 to determine which components should be replaced by a field service technician. Memory problems Symptom FRU/action The amount of system memory displayed is less than the amount of physical memory installed. 1. Verify that: • The memory modules are seated properly. • You have installed the correct type of memory. • If you changed the memory, you updated the memory configuration with the Configuration/Setup Utility program. • All banks of memory on the DIMMs are enabled. The computer might have automatically disabled a DIMM bank when it detected a problem or a DIMM bank could have been manually disabled. 2. Check POST error log for error message 289: • If the DIMM was disabled by a system-management interrupt (SMI), replace the DIMM. • If the DIMM was disabled by the user or by POST: a. Start the Configuration/Setup Utility program. b. Enable the DIMM. c. Save the configuration and restart the computer. 3. DIMM. 4. System board. ✏ NOTE See "System" on page 104 to determine which components should be replaced by a field service technician. Microprocessor problems Symptom FRU/action The blade server emits a continuous tone during POST. (The startup (boot) microprocessor is not working properly.) 1. Verify that the startup microprocessor is seated properly. 2. Startup microprocessor. 88 SBXL52: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
88
SBXL52: Hardware Maintenance Manual and Troubleshooting Guide
NOTE
See “System” on page 104 to determine which components should be replaced by a field service
technician.
Memory problems
Symptom
FRU/action
The amount of system
memory displayed is less than
the amount of physical
memory installed.
1.
Verify that:
•
The memory modules are seated properly.
•
You have installed the correct type of memory.
•
If you changed the memory, you updated the memory configuration with the
Configuration/Setup Utility program.
•
All banks of memory on the DIMMs are enabled. The computer might have
automatically disabled a DIMM bank when it detected a problem or a DIMM
bank could have been manually disabled.
2.
Check POST error log for error message 289:
•
If the DIMM was disabled by a system-management interrupt (SMI), replace
the DIMM.
•
If the DIMM was disabled by the user or by POST:
a.
Start the Configuration/Setup Utility program.
b.
Enable the DIMM.
c.
Save the configuration and restart the computer.
3.
DIMM.
4.
System board.
NOTE
See “System” on page 104 to determine which components should be replaced by a field service
technician.
Microprocessor problems
Symptom
FRU/action
The blade server emits a
continuous tone during POST.
(The startup (boot)
microprocessor is not working
properly.)
1.
Verify that the startup microprocessor is seated properly.
2.
Startup microprocessor.